Visit Brian Dudley's homepage! | |
11-13-2020, 01:43 PM | #3 | ||||||
|
Brian,
If the weep hole creates more issues as you have said (assume you are not lying!) would it be a positive action to plug that weep hole? Scott Hanes |
||||||
11-13-2020, 05:39 PM | #4 | ||||||
|
I have been known to lie often. So you just cant trust a word I say. Even when confronted with people that have 40 years experience in knowing it all.
I say that they cause more issues than they prevent because yes they allow moisture out if it gets in. But the hole guarantees that it will get in. Vs if the set is tight to start with, it wont get in at all. And getting it out through that singular weep hole is a little bit of a pain after the fact once the bluing job is done. And during the actual bluing process, water will leak out some from the hole which can cause issues with streaking your rusting applications and such. After the job is done and all is dried out and oiled, it does not really matter if the hole stays open or not. But if one wants to plug it up, a piece of lead shot tapped into the hole does the job. This is just based on my own experience in bluing barrels and dealing with weep holes in them.
__________________
B. Dudley |
||||||
The Following 7 Users Say Thank You to Brian Dudley For Your Post: |
11-14-2020, 10:02 AM | #5 | ||||||
|
Thanks for your thoughts! Does anybody have a serial number range that the weep holes were first drilled?
|
||||||
11-16-2020, 10:43 PM | #6 | ||||||
|
It sounds to me like the early guns without the weep hole can be reblued without drilling a hole which might make it tougher to tell if the barrel has been reblued.
|
||||||
11-16-2020, 11:04 PM | #7 | ||||||
|
If the barrels were reblued with the proper bluing and polishing technique what difference would it make if they had been redone?
Most early guns had barrels of composite steel , either the various forms of twist , laminated or Damascus , which were generally not factory blued anyway. Many early composite barrels have been worn or oxidized to such extent that the pattern is obscured and refinishing may be advantageous . Most questions about Parkers are answered in The Parker Story. TPS provides an explanation about when the weep holes in barrels appeared. |
||||||
The Following 4 Users Say Thank You to Bruce Day For Your Post: |
11-17-2020, 09:39 AM | #8 | |||||||
|
Quote:
|
|||||||
11-17-2020, 11:28 AM | #9 | ||||||
|
If a gun was built at Ilion (post mid 1937) then it would have had a weep hole originally. If it was an earlier gun that was re-blued by Remington during manufacture or up to the time that they stopped factory service (early 1950s) then it would have a weep hole, BUT also a remington repair code on the barrel flats.
So, if you are looking at a gun that is prior to the move to Ilion, and it has a weep hole, but no repair codes, then it was reblued and weep hole drilled by some other party.
__________________
B. Dudley |
||||||
The Following User Says Thank You to Brian Dudley For Your Post: |
11-17-2020, 11:55 AM | #10 | ||||||
|
Regardless of who, where or why a weep hole was drilled.... why did anyone think these weep holes had to be so large in diameter. Most of the ones I have seen are about 1/16" - 3/32" in diameter. All that needs to escape from said hole is steam, not actual water. If it is suspected that there is moisture beneath the ribs, all that needs to be done is to bring the barrels up to 212 degrees (not nearly warm enough to melt the solder) and the steam will escape by expansion through a nearly microscopic hole...
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|