|
 |
 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
07-15-2023, 05:53 PM
|
#3 | ||||||
|
New to me and I've seen a few Lefevers.
|
||||||
|
|
||||||
 |
 |
 |
|
|
|
07-17-2023, 08:07 PM
|
#4 | ||||||
|
Breck: that is a Bernard variant; possibly similar to this which I think is "Bernard Ribbon"
 And the pieces don't match. The top looks like 3 iron "oxford" and the bottom "horseshoe" - must have used whatever was handy 
__________________
http://sites.google.com/a/damascuskn...e.com/www/home Last edited by Drew Hause; 07-17-2023 at 08:54 PM.. |
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Drew Hause For Your Post: |
|
|
|
07-18-2023, 12:30 PM
|
#5 | ||||||
|
Breck,
Your assessment as to what happens seems logical to me. Material was added.
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
|
|
|
07-18-2023, 06:09 PM
|
#6 | ||||||
|
I thought it looked like Bernard too. I even wrote it in my notes, then I wasn’t sure, and scratched it out. Great catch.
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to Breck Gorman For Your Post: |
|
|
|
07-22-2023, 02:34 PM
|
#7 | ||||||
|
__________________
http://sites.google.com/a/damascuskn...e.com/www/home |
||||||
|
|
|
||||||
|
|
|
|
|
|
08-02-2023, 03:52 PM
|
#8 | ||||||
|
That is quite an interesting addition. Someone at Lefever must have been a little heavy handed on the milling machine. Could you see a brazing line on any of the sides?
__________________
Channing Will Will Bros. Restoration |
||||||
|
|
|
||||||
|
|
|
|
|
|
08-21-2023, 11:10 AM
|
#9 | ||||||
|
I have never seen a pecelike that, but I did buy an oddity not long ago that seems related. It was a French 10 gauge hammer single fowler that had a Damascus barrel that had a heavy octagon rear portion that stepped down at a wedding ring to a round lighter diameter. The barrel was Damascus but the thicker octagon section was twist. My guess was that it was a lighter damascus overlaid with twist during the welding to give the diameter needed for the octagon section. Odd.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
08-21-2023, 11:40 AM
|
#10 | ||||||
|
Art: the French adopted Pieper's "Diana Breech" monobloc construction (or maybe Pieper stole the idea from the French?) and it is more likely that the breech monobloc was damascus and the tube twist.
Lots of Pieper's "Modified Diana" barrels (no step down) had a steel breech and damascus tubes 1882 
__________________
http://sites.google.com/a/damascuskn...e.com/www/home |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Drew Hause For Your Post: |
 |
|
|
Linear Mode
