Original Brass Shells
 

Hello Everyone,

I bought an 1880 lifter this past spring and it came with 18 Parker 12A Brass shells along with primers, powder and some reloading tools. My first question is age..how long did Parker/UMC make these shells? I was able to find a date online regarding the almost full primer tin and I found that they were first made in 1884(though I don’t know how old these might be). Overall I was just curious on how old all of this might be and if it could it be close to the age of the gun.

I cleaned 2 shells with the idea of shooting them just to do it, I wouldn’t use the powder in the picture, but that came with all of my “goodies” as well. Does anyone still shoot these original shells? Is there a good source for primers for these older shells? I had a hard time finding any others online.

I do think I’ll order some off the replica Parker Bros. 12A shells from Track of the Wolf as I have really enjoyed the 10ga. versions in my short ten.

Let me know if I should put this original stuff away and just be thankful I have it with the gun.

Thank you,

Jay

I wouldn't use the powder or the primers. Keep them with the gun and use Track of the Wolf shells and whatever more modern components you can find.






.

Mr. Oliver:
Dean is correct. The materials you got with the gun should be considered "collectibles" and not used. Especially the brass cases. Brass often has a tendency to "age crack" and/or embrittle with time. This is why various armed forces sold off ammunition after so many years. The didn't consider it reliable any longer.

Best to stay with current components if you intend to shoot the gun. And an inspection by a competent double gunsmith would be advised as well.

I have old original brass shells. The 10ga use large rifle or pistol primers, the 12ga small. I would think one or the other would fit. Sounds like you got a real nice buy.

Old primers sometimes contained mercury, and it was the mercuric primers that could cause the embrittlement in the brass, as well as contribute to corrosion of the bore.

Thanks for the replies. I only got excited about all of this when I realized I had all of the components to possibly shoot some shells that this gun may have shot over a 100 years ago. Does it hurt the collector value to clean the shells? I thought it might which is why I just cleaned 2.

The gun is mechanically sound and I have shot 8 boxes or so of RST's through it. I posted some pictures when I bought it back in the spring. Its a grade 2 with 32" barrels. I was loading my newer brass 10 gauge shells and thought about using brass shells in this 12. That's what got me started on this and I was curious as to how old the shells and primers might be.

I appreciate the advice and I will not use the shells. I must admit though, the 2 I cleaned fit perfectly in the chambers...

Thanks again,

Jay

If you have multiples, I see no reason to not load a few and shoot them, albeit with fresh components. If you're shooting the gun, why sweat loading and shooting the brass cases?

It won't hurt the value if you CLEAN them. Heavy crud can be carefully scraped off. A brass bristled 'tooth brush', from your local hardware emporium, can be used vigourously to remove various forms of verdigris. Quite often the brass will remain stained, which is understandable. Good Luck!

As with any antique that you intend to clean while retaining its original beauty - never use an abrasive of any kind. Soak them in a solution that will eventually dissolve or at least soften the crud. They may need to soak for weeks... then use a soft nylon toothbrush on them while they are still wet.






.

They may have been reloaded at one time with corrosive primers. Very difficult to tell if a case is bad. Older cases often have folded heads not solid like new brass and are much weaker.

Rifles generally have a gas escape path for this situation. Look at the hole left side of a 03 Springfield action. It's to let gas escape with out harming the shooter. Shotguns don't have a good escape path because they operate at much lower pressure . Even so Puncture a primer gas will blow back in the action around the firing pin, whole case head lets go it's likely to come out between the barrels and action standing breech.

Not a risk I would take

William