Parker Gun Collectors Association Forums

Parker Gun Collectors Association Forums (https://parkerguns.org/forums/index.php)
-   Parker Reproductions (https://parkerguns.org/forums/forumdisplay.php?f=22)
-   -   16 ga Repro (https://parkerguns.org/forums/showthread.php?t=15822)

Scot Cardillo 03-06-2015 09:20 PM

16 ga Repro
 
I have a thread in the wtb section but figured any discussion/q's should be here in the Reproduction section.

I recently treated myself to "The Parker Story" and read that the 20/16 was offered a bit late in the game..I also read that for those that already owned a 20ga that a 16ga set of barrels could be added to it.

My question is this - if adding a set of bbls to an existing 20ga..did the factory (not offshore but here in the states) offer fitting to the frame and to the forearm? Also, were the new bbls serialized to the gun it was added to?

~Scot

Bob Jurewicz 03-07-2015 07:17 AM

It is my understanding that Krieghoff here in the States did the fitting and numbering to gun. I have seen unfitted-unnumbered barrels that never were matted to a gun.
Bob Jurewicz

Rich Anderson 03-07-2015 09:06 AM

I am not aware of any factory two barrel two gauge sets other than the Reproduction 20/16 and as mentioned those barrels were from Kreighoff. The National Sporting Fraternity offered a limited number (1000) of these two barrel sets and the serial numbers matched.

Bob Jurewicz 03-07-2015 09:14 AM

Information is that a total of 500 16 GA Krieghoff barrels were obtained. Not all were fitted to create 20/16 sets. Some found their way to the aftermarket. Some may even have been destroyed.
Bob Jurewicz

Rich Anderson 03-07-2015 09:29 AM

I know for a fact that the NSFL commissioned 1000 16/20 sets for their members. Limited edition guns , books ect was one of the benefits of being a member. They might not have produced all of them but I bet they did. I remember when they came out I wanted one bad but just couldn't afford it.

Scot Cardillo 03-07-2015 01:45 PM

Thanks for the additional info gentlemen

Are the Krieghoff barrels marked, "Winchester Parker Reproduction"..if not, what is a sure fire way to discern original bbls from CSMC supplied bbls?

Have I read somewhere that the rib matting/engraving stops short of the dolls head on the CSMC bbls unlike the originals which are engraved typical of all Repros?

Bob Jurewicz 03-07-2015 02:23 PM

They are marked in script on the left side of the barrel "Parker Reproduction" and stamped "Krieghoff Ulm" on the left barrel flat.
Bob Jurewicz

Russ Jackson 03-08-2015 10:42 AM

I had recently seen a 20/16 set for sale and the 16's were marked on the Barrels , Made in Germany ,would these be correct ? I wasn't interested in the gun just wondered when I seen it if it was correct !

Scot Cardillo 07-28-2015 11:10 AM

For those that were paying attention at the time - When did Galazan offer the 16ga bbls which were designed for the 20ga guns?

Early/mid 2000's or am I a decade off?

Dean Romig 07-28-2015 02:31 PM

It was mid-late 2000's. I bought a set and the rib matting did not cover the doll's head but as I recall, the doll's head was cross-hatched engraved and the matting went as far as Remington rib matting went.


All times are GMT -4. The time now is 11:30 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org