Parker Gun Collectors Association Forums

Parker Gun Collectors Association Forums (https://parkerguns.org/forums/index.php)
-   Parker Reproductions (https://parkerguns.org/forums/forumdisplay.php?f=22)
-   -   Repro for ducks and steel shot (https://parkerguns.org/forums/showthread.php?t=12050)

Eric Grims 12-01-2013 09:42 AM

Repro for ducks and steel shot
 
Starting to enhance my gun buying mad money pot as I want a repro 12 gauge to shoot steel for waterfowl next season. Lots of time to look until summer. Lots of 26 inch guns out there but would like the 28" IC/Mod. A two barrel set may be an option if I can find the right choke configuration. I am not into opening the chokes on such a nice gun.
I was wondering if folks thought this gun was a legit factory made interchangeable choke gun. I was not aware they made them other than the SC models.

http://www.gunsinternational.com/Par...n_id=100393180

Thanks

John Dallas 12-01-2013 10:46 AM

Is that a crack on the right side of the head of the stock?

Eric Grims 12-01-2013 11:31 AM

I was wondering this myself. Sure looks like it.

Greg Baehman 12-01-2013 11:38 AM

I believe that is a Sporting Clays Classic Model. You could verify that simply by asking the seller if it's stamped 'ISC' on the barrel flats and if the muzzles are slightly flared (to accommodate the screw-in chokes of the time period in which they were produced). If it indeed is a SCC it will also be roll stamped on the left barrel as having 2 3/4" chambers, but the chambers will likely measure 3".

I agree with Big D that it does look like a crack on the right cheek.

Marty Kohler 12-01-2013 12:26 PM

Since it has been brought up, What are every ones thoughts on shooting non toxic thru repro screw in chokes (12 gauge sporting clays model) for instance........ could not find much searching...Thanks, Marty

Greg Baehman 12-01-2013 12:50 PM

According to this article written by Gene Hill on the Sporting Clays Classic, this model was designed for the use of steel shot providing you don't use tighter than a Modified choke tube. With the quality of today's steel shot loads that are available is there any reason to shoot the $3-a-pop non-toxic loads in a Repro designed for steel?

Ater reading the 1st page you'll need to click on "Previous Page" to read the 2nd page, as they are out of order.
http://parkerguns.org/forums/album.p...&pictureid=978

Steve Kleist 12-01-2013 07:08 PM

Eric,
I'm sure there are other Parker members who will reply also.
As I'm sure you know, a 2 3/4" load is plenty for ducks and the SC models will fit your needs. I have a 3" Repro with Briley aftermarket thin walled screw in chokes. I went with this choice as a stock/forend and double trigger configuration. It is convenient to have 3" chambers but not necessary in my opinion. My gun gets plenty of use and a delight to have in the blind.
Good luck on your quest.
Best Fishes,
Steve Kleist Ely, MN

Destry L. Hoffard 12-01-2013 08:22 PM

I'm with Steve on this one, I rarely shoot ducks with anything but 2 3/4 anymore and have good success. I used to think I had to shoot 3 inch at them but once I started shooting guns that actually fit me and threw good patterns I figured out I didn't need it. I do sometimes shoot heavier 1 3/8 or 1 1/2 ounce loads when on a pass shooting venture and the ducks are 50 yards plus.

That being said, I've got a Super Fox that's back from the stocker and needs some action. I've got a couple cases of the 1 5/8 Kent TM loads for it, those should be a dandy long range choice.

Eric Grims 12-02-2013 05:02 AM

I am under the impression that all repro barrels fixed or screw in are steel shot compatible.
Is that correct?

Eric Grims 12-02-2013 05:04 AM

Add:
Excluding any full choked barrels.


All times are GMT -4. The time now is 01:28 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2025, Parkerguns.org