I have a PG trigger guard belonging to a Bernard CH No. 68071

Left hammer for 34275
 

I know this is a longshot but need the left hammer for Gr2 top lever, 1 frame, s/n 34275. Actually any hammer would do.

looking for the forend - or at least the iron for # 70168

the gun is currently wearing the forend for 64448

I have forend wood and tip for 0 frame 20g. VH No. 150314

Given that it is with tip, that is a dead ringer that the gun is now wearing an aftermarket BTFE.

149974
 

Would like to locate for possible purchase VH serial number 149974

86842
 

According to PGCA letter this GH was sent back to Parker for a set of 40" barrels. I have the rest of the gun, well most of it.

Looking for number 153669

books as a DHE 12g. with 34" barrels.

Looking for 79281

Should be a GH 12 gauge.

241761
 

Looking for receiver and butt stock for 241761 . I assume it is a V grade gun with Ilion markings. I have barrels and SFE.

There are still a bunch of posts on this thread that either have serial numbers with commas, or serial numbers with punctuation marks adjacent to the numbers. The SEARCH function will not work for people wishing to connect with you. The number should be separate from all other characters, like 200000 .

Perhaps the moderator would let you or me correct them?

George, I think that is a great idea. I hope it somehow comes to fruition.

228908
 

I have the original stock it's uncut, has the original skeleton steel butt plate. Stock was broken and repaired at the wrist. Great piece of wood if you have the gun, I'm sure this can be restored. According to the book it's from a DHE with factory single trigger.

30" Titanic barrels
 

Talk about a DUH! moment, I pulled out a DHE 12 that was in the back of the safe to make room for the guns I just cleaned from a recent hunting trip. Well to my surprise I noticed that the forend lug and forend iron were both stamped with a 2. Hmmm.... went to my letter from 2007 and the gun left the factory with 30" barrels, so the current barrels which are 28" must have been added later. Never noticed this in the 10 or so years I've had this gun, no mention of them in the letter.

So I'm looking for 30" barrels and forend for 198638.

Thanks for looking.

I am looking for a 2nd set of barrels for my gun. The number is 26101 thanks, frank

28" 20ga damascus barrels
 

I am desperately looking for a set of 20ga 28 inch damascus barrels, "0" frame with ejectors. I would love to find the originals, serial number 84040 but any other 20ga 28" damascus "0" frame set will work even if extractor.
Thanks, David

74474 I have set number 2 ph 26 inch barrels. Looking for barrels and forearm from set number 1.
Thanks Al

16 gauge O frame damascus barrels
 

Please someone out there must have a set of 30' 16 gauge O frame Damascus barrels, the gun is an ejector gun but I'll take a extractor set. My gun started life as a 16 ga on an O frame and was sent back to Remington to be fitted with 20 and 28 ga fluid steel barrels, I think Remington destroyed the 16 ga barrels:banghead: Eric

Most likely Remington, Lefever, and any other business that replaced Damascus barrels with fluid steel barrels destroyed or scrapped the originals.... They were Dangerous!!






.

Looking for a friend. 16 gauge VH (I think) Parker 225314

Hang tag that goes with it

Mills
Post the tag on the Hang Tag List thread as well. its a sticky.

I have the buttstock for 6979 anyone have the other bits?

VHE .410 222955 I have your forend latch.

Wow.........

I wonder how a .410 Parker survives without a forend latch.

Likely now sporting a beavertail of sorts. The curvature of the top of this latch is pretty tight and a latch from a larger frame size probably fit the profile of the beavertail wood better.Just a guess ... Roger

Looking for a set of 26" 12 ga Vulcan barrels for 71910

197425
 

I have a fore end for 197425, which was a 2 Frame, 30" VHE

I have 28 GA. R.H. ejector for XXX042

I have 28 GA. L.H. ejector for XXX358
Neither has any obvious problems.

Sorry about those X's but the last 3 is all we get.....Roger

P.S. Stay tuned as I dig further into the cave :corn:

They will fit a Repro... I've done it. And I believe the frame size is of no significance in ejector parts.






.

Dean if my poor memory is correct the sear slides are frame size specific and I believe the ejectors as well since the center to center on the chambers will vary with frame size...Roger

Maybe Brian will give us an experienced opinion. I think I've read where he had indicated that the ejector mechanism in the forend is not frame size specific.





.

That was an experienced statement not an opinion. Others with Parker ejector experience are more than welcome to comment on the subject....
The sear slides are frame size specific since it must align with the plunger pins that exit the front of the frame at the same center to center measurement as the firing pins depending on frame size. The ejectors which eject the spent cartridge from the chamber are gauge and frame size specific. There are parts in an ejector forend such as hammers and mainsprings that are not frame size specific. Kindest regards,Roger

Right Roger - that's exactly what I said "the ejector mechanism in the forend is not frame size specific." Most of the parts you reference are in the barrels or in the frame.





.

Looking for original barrels to 118830

Barrels
 

Long shot look for barrels for 16g hammer Parker 14081. Thanks

Still looking for Titanic Steel barrels (length unknown; unspecified in letter) for 88653. Thanks, Kevin. 16 ga. BTW

found 77110 complete forend

Jon Weber, Edgar, Kevin and a couple of others will never find their mates if you continue to place punctuation marks next to your serial numers. Separate the numbers from punctuation marks and other text.