Chamber Length
 

Dave; Parker Pages editorially advertised for a citation to verify that chambers were cut shorter than shells in Parker's era. Ed Muderlak found a 1933 article based on 1932 work that we scanned and reprinted. That article was written by a person with good industry credentials but covered only one gauge and shell length; 3 inch 410 in 2 1/2 chambers. The three inch shells produced better patterns in the 2 1/2 inch chambers, but the author noted an inch of case was burned away in the process.
We will put out the call again in the next issue, in search of such information printed in the pre 1929 era. We know that Parker Bros was a member of the industrial fore runner to SAAMI in the 1920's when they began stamping "overload proved" on barrels, but I have not been able to obtain a copy of those standards through SAAMI.
I have always considered those tables in the Remington Salesmen's Catalog to be a typo/transposition when I have my editorial hat off. The current SAAMI standard clearly calls for short shells in long chambers. After reading your post I measured a few modern barrels with the equipment I used to measure the Super Fox. My Rem 3200 labelled "Trap" measures 2 7/8 inches; my ca 1985 Ruger Red Label marked 3 inch measures 3 3/16 inches, and my 11 87 trap barrel measures about 3 inches.
I have seen some anecdotal accounts that M21's were short chambered in the 1930's but have no physical evidence to verify this.
I obtained my first hunting license in 1950. My hunter training instructor warned us that "low brass" shells were no longer shorter and lighter as they were in the time before WW2, and that if we were told by an elder that low brass was ok in old single shots and break open guns, we should have the individual guns examined before using "modern" ammunition. I became a hunter safety training instructor in 1964, and my NRA correspondence course contained the same warning and information.
I also note in Stadt, that Winchester changed the designation of the M1893 to M1897 when they adopted the 2 3/4 chamber. Stadt also notes that 2 3/4 inch shells were labelled "Repeater" on the box.
We (Parker Pages) and I would really like to clear this up. A copy of that 1920's industry standard would be a good arbitrator.

Best, Austin

Austin, SAAMI ( Sporting Arms and Ammunition Manufacturer's Institute) is headquartered in Newton , CT . Although its usually difficult to get one of these minimally staffed trade organizations to conduct any file research for persons who are not members of the organization, perhaps they would allow access to a researcher. Current standards are available on line. Maybe we have a member who lives in Connecticut ?

Hey Dave, good to hear from you. My Mahoney setter "Jussie" just turned 7 in march. He is still hunting strong. We had a good season for woodcock and grouse. still shooting my modified 20 gage fox sterlingworth, but i am looking forward to shooting the parker. Is you dog working out well for you? pete

Sorry Bruce,Nobody here in Connecticut that I know of....

Austin, I don't have the drawings and specs in front of me, but we have found several instances of Parker Brothers memos and drawings that specify chambers 1/8" shorter than the shells meant to be fired in those chambers. We have also seen Parker Brothers hang tags specifying "2 5/8 inch chambers for use with 2 3/4 inch shells." We have also seen Parker Brothers orders specifying the same thing. I believe I have articles from older American Rifleman magazines noting that this short chambering is somewhat of an industry standard, although not universal. These Parker Brothers standards continued into the Remington era. I think it would be very easy to confirm by examining stock book entries from the twenties that indicate that a gun has been built with 2 5/8" chambers and proved and patterned with 1 1/4 ounce shot loads.

Long Shells in Short Chambers
 

Bill; I would really like to find a solid pre 1920 reference to this long shell in short chamber pattern theory. I think Askins the elder alluded to it but did not verify or explain it.
The bore jig I used to measure the Super Fox allowed me to make some quantitative measurements about this. One of my own "competition" guns is 136683 that dates from 1906 and was made to measurements by DuBray. It shoots beautifully tight, round patterns with both barrels. It is chambered 2 3/4 inches; the front of the forcing cone has a long taper ending at the barrel diameter of .740 inch at 6 inches from the breech, and one choke is more parabolic than like Oscar's "OGEE". I have a VHE with btfe and monte carlo, no safety 170789 , 32 inches that shoots similar round patterns. It is also 2 3/4 chamber with the forcing cone taper meeting the bore of .738 at 5 inches from the breech, and again a more parabolic choke in the left (full) barrel. A third 32 inch PH (207489) also reaches .738 at five inches, and the left barrel choke begins at .740 five inches back from the muzzle with a more parabolic than ogee taper. These dimensions do not duplicate the Super Fox, but the forcing cone taper and choke taper is of the same form.
These three guns tell me either that these owners sent their guns to Becker, or that King knew how to produce these patterns with forcing cone and choke profiles that did not involve jamming the case mouth into the forcing cone.
I have some "new" primed 3 inch ten gauge paper cases from two makers that have never been loaded or fired. They measure 2 7/8 inches precisely. I would like to find some unloaded twelve ga cases to measure.
The Super Fox has beautifully tapered chokes and forcing cones. The chambers measure .788 - 792 at 2 5/8 from the breech. The most common plug type chamber gauges are .792 wide. I did not measure the Super Fox with a blade gauge, but it may have measured 2 5/8.
Multiply fired modern 2 3/4 cases measure 2.66 +/-. Squaring the ragged mouth would shorten them a little. Were paper 2 3/4 cases also 2 5/8? We need some unfired cases to measure.

Best, Austin

"Were paper 2 3/4 cases also 2 5/8? We need some unfired cases to measure."


Austin, I just took a quick look at some unfired paper hulls I have stashed away and found a 12ga paper Federal "Monarch" measures 2 5/8, a 10ga "Leader" 2 5/8, and a 16ga "New Rival" 2 9/16. HTH, Bob

Austin, first you wanted a reference that guns were made for longer shells than the chambers. I gave you those references. Now you changed your mind and want a 1920s reference for how such guns pattern with long shells. You can find anything you want in Askins' articles because he was in the word selling business. One month he would write that short shells in long chambers throw great patterns, next month they will throw bad patterns. I just read an Askins article from 1916 where he tests shot containers. In the lengthy article, he doesn't really reach a conclusion or compare his patterns to patterns without using shot containers. Why did he do that. Simple, to sell another article next month, in which he may actually reach a conclusion. Or maybe not.

Food for thought or stirring a pot?
 

A few thoughts. If indeed Parker chambered guns 2 5/8" for 2 3/4" shells and it was an industry standard;

How long was that practice carried on by Parker?

How long was that practice carried on by any other Maker?

Why did they change?

If they changed to meet "standards" did Parker or Remington lengthen chambers upon request or as part of any repair?

If Parker was still in business would they lengthen chambers on older guns or not? (I realize this is pure speculation).

Finally, because this is hot button topic I wonder if there may be those among us who think lengthening chambers is a good idea or OK but don't bring it up because they don't want what they might consider to be unecessary harsh critcism from the board?

If it doesn't matter if you don't do it, and the gun is a "shooter" and not unique, does it really matter much if it is done?

A Trojan 20 is a fine gun, I like mine, but it's a Trojan and I don't think lengthened chambers undercut overall condition/price if it's nice and original otherwise.

Chamber Length
 

Sorry Bill; I am really looking for a solid citation about this irrespective of who prepared it. I think that the experimental results of measurement of Parker competition guns, and Super Foxes are in direct conflict with the idea that long cases in short chambers produce better patterns than short chambers and short forcing cones. I would really like to find the original, and continuing publications that present the short chamber theory.

Anyway; I look forward to seeing you and Kevin Saturday.

Best, Austin