My friend, Daryl, obviously subscribes to my philosophy concerning tight chokes. "Learn to shoot." I have seen Daryl shoot and "he don't need no open chokes".

What should the constrictions be for 28ga. Repro 28" M/F barrels? Briley choke chart says M/F should be .015/.024. Had my 28ga. 28" M/F barrels measured and the results were right .020 and left .045. Isn't this tight? I previously mentioned somewhere in this post I was obliterating pheasants over a pointing dog with the right Mod barrel under 20 yards. Could this tight choke be why or what am I missing? What measurements should 28" M/F barrels have?

My 28ga. 28" Repro's factory-original M/F chokes are .014/.034. I love them for 5-Stand and Sporting Clays, but aren't my first choice for much of the other close-range shooting that I do, such as grouse/woodcock and Skeet. For grouse/woodcock I'm shooting the 26" IC/M at .006/.016 and for Skeet I find the 26" Q1/Q2 chokes at .004/.007 about perfect. I've got a 2-bbl. set and a single barrel set that all three barrels sets are interchangeable between the two 28ga. Repros.

Certainly at lot of what one needs it based on the game one hunts most of the time. Since 80% of my shooting is Woodcock over Sophie, the Q1 and Q2 chokes should be the bee's knees out of my 28 gauge Parker Repro. FWIW, I currently shoot a Fox Sterly 20 gauge with chokes of .004 and .014 and I have destroyed Woodcock with the first barrel when centered at the normal distance of circa 15 yards. Where I hunt there is often zero chance of getting a second shot because of thick cover and even it I do that second shot will be max of 25 yards. For those who like to eat Woodcock a centered bird even when using open chokes at close range often turns into a skeet station 7 outgoing. An explosion of feathers and the dog trying to figure out what pieces to pick up.

HOLY…. .034” is full choke for a 12 gauge, but in a 28 gauge ???





.

I am hoping to come across a 28 Gauge Repro that tight for turkeys.

I have never heard of a 28ga. choked at .045". .021" is considered by Briley to be a full choke in a 28.
It's no wonder you were 'obliterating' game. You could shoot through a Cheerio and not break it.

my 28 gauge repro with 28" barrels is choked M/F...measured .016/.035...mod/super-duper full according to people smarter than me! I am probably going to have Jim Eyster open it to something in the .010/.020 range...I have been advised by many more wise than I am to stay a bit tighter with a 28 gauge...I have an Uggie 28 gauge that I had opened up to SKT1/SKT2 after getting it...have killed lots of sharpies and huns, and some ruff's with it...I will say I do cripple lots of birds...may shift to a 15/16 oz load of 7.5's instead of the normal 3/4 oz of 8's that I usually hunt with. I have a red label 28 gauge as well...haven't shot or hunted it much, but have done well with it...probably using IC/Mod tubes when I have hunted it. If I were going to describe what I am looking for with the repro, it would be LM/LF, basically...knowing I can have it opened further if need be. It will probably be used mainly for prairie birds in Sept/early Oct, pre-pheasant season...maybe a pheasant hunt or two? Great forum, much fun!!!!:)

YESSIREE, only .034! Others here have reported even tighter -- like .039 and even .040 or more. One here even asked I wonder how the wad clears the bore? When shooting tight chokes in a 28 Eightbore says "Learn to shoot". I agree as these tight chokes make for some impressive breaks on those high 50+ yard crossers...lead 'em by a canoe length and they go poof!

I have two full choke 28 Repros. They both measure .039 with a very expensive Galazan mechanical bore gauge. I have always wondered about what happens to the wad on the way out of that bore.