PDA

View Full Version : forend


Mark Callanan
01-09-2013, 04:38 PM
I need to replace a cracked forend
Its a VH grage
What info do I need to add to my add to get the right parts?

Thanks for any help ...

Steve Huffman
01-09-2013, 04:43 PM
Can it be fixed ? If not frame size and gauge , serial number would date it . Also if it has ejectors or extractors

Mark Callanan
01-09-2013, 04:45 PM
Serial number is 230xxx
VH Grade
I need the wood only
Any other info that I should list for the add?

Rick Losey
01-09-2013, 04:52 PM
that should be enough for the ad, are you sure the crack cannot be fixed?

and have you checked here
http://www.pugsguns.com/findCategory.action?id=8

Steve Huffman
01-09-2013, 04:54 PM
Ejectors or extractors ? 230xxx is not in the book . If you are sure its not A VHE the E wont be on the water table,

Mark Callanan
01-09-2013, 05:12 PM
Ejectors or extractors ? 230xxx is not in the book . If you are sure its not A VHE the E wont be on the water table,

It is a VH
I am not sure what you mean not in the book?

Rick Losey
01-09-2013, 05:13 PM
It is a VH
I am not sure what you mean not in the book?

he is referring the serial number reference book - used to check the original specs

http://www.amazon.com/Parker-Identification-Serialization-Charlie-Price/dp/1886768374

often found on that auction site

Dean Romig
01-09-2013, 05:33 PM
A 230,thousand range gun is likely not to have any surviving information that is in the posession of the PGCA.

Mark Callanan
01-09-2013, 05:40 PM
he is referring the serial number reference book - used to check the original specs

http://www.amazon.com/Parker-Identification-Serialization-Charlie-Price/dp/1886768374

often found on that auction site

Ok got it
I do have that reference book
Thanks for the information

Mark Callanan
01-09-2013, 05:46 PM
Can it be fixed ? If not frame size and gauge , serial number would date it . Also if it has ejectors or extractors

Frame is 1 1/2 12 gauge

Steve Huffman
01-09-2013, 05:52 PM
The one I have wont fit its for a 16 0 Frame sorry

Linn Matthews
01-09-2013, 09:05 PM
DelGrego can make one for you

Mark Callanan
01-09-2013, 09:24 PM
DelGrego can make one for you

Well i paid 950.00 for the gun
I assume it would cost 400 plus
So I was posting here to try and find a used part
Still looking..
Thanks all for the help so far...

Bill Murphy
01-10-2013, 08:24 AM
A VH Grade 1 1/2 frame forend wood should be fairly easy to find. Fixing a crack may be the best option, however.

John Campbell
01-10-2013, 09:10 AM
Unless your forend is completely trashed, it can most likely be fixed... and virtually invisibly -- at least by a pro. It will be MUCH cheaper than a new forend, too. I hesitate to suggest resources for this lest I be denounced as a shill.

Best, Kensal

Mike Phelps
01-10-2013, 12:33 PM
You can email the folks here with some pictures. There were helpful assessing my stock
http://www.stockfixrs.com/

Brian Dudley
01-10-2013, 09:01 PM
If you are looking for a replacement forend, it is also important to note the length of the iron. There was some variation in the lengths. I have observed some iron tangs that are 4.5" long and others that are 4.75" long. The screw spacing on all are the same.