Someone must be on drugs!

[John Dallas]

Stopped by a table at the OGCA warzone which had a number of interesting guns - CSM Model 21 o/u's, Winchester M21's and two Parker Repros. Each set was a DHE two barrel set, each with 28 and .410 barrels. I didn't check frame sizes, but each was priced at $17,000. I suspect he's going to walk them around to a few more shows

[Jay Gardner]

Someone feel free to correct me but I believe that's pretty much the going rate for a 28/410 two-barrel set. Relatively rare.

[Rex Northen]

Is anyone really paying that? I know they may be rare, but there are an awful lot of great guns out there at $17k

[Brett Souder]

One of those sets had a straight grip, double trigger and beaver tail forend. Both were missing their cases and only had one forend for each pair?

[Jay Gardner]

I know of a 28/410, 3-barrel set, cases and unfired. What do you suppose that one is worth?

[Kenny Graft]

A correct 410/28/28 three barrel set in a hard to find combination should bring about 18500.00 Those sets are so scarce only one just like it may exist! DT-SG-two BTF, 410 ic/mod, 28 Q1/Q2, 28 M/F I know of only one set like this....(-: Yes you could get a Spanish special order built like this for a bit less.....but its not a parker!!!! SXS Ohio

[King Brown]

A Repro isn't a Parker, either. It's madness.

[Mills Morrison]

It might be a reasonable price and might be unreasonable, but I know there are other guns I would rather have for that price.

[Kenny Graft]

I see them now listed on gun broker......I would like to see them in person. He lists them with 28" 410 barrels! One set is F/F They look correct, PR barrel stampings. I know some of the A1 specials repro's had 28" tubes but never a set on a DHE grade. SXS ohio

[Richard Skeuse]

Hi Guys I looked on Gunbroker and did not see the 28-410 Parker reproduction listed. Do you have an item number for it Thanks and hope all are well

[Jay Gardner]

Richard,

Here you go:http://www.gunbroker.com/Auction/ViewItem.aspx?Item=536793143

JDG

[Greg Baehman]

. . . and here's the other one. Sit back and ponder for a moment what the ask might be if the guns included the original case and 2nd forend.

http://www.gunbroker.com/Auction/ViewItem.aspx?Item=536789739

[Richard Skeuse]

Thanks Guys. if someone wants to PM me I am at rskeuse@reagentchemical.com

[Brett Souder]

I'm not sure of the item number but search under Parker rep to and it will show up.

[Brett Souder]

Search under Parker repro. Smart phone error.

[Greg Baehman]

Did you happen to notice the frame size markings on the lugs of each of the .410 barrel sets of these two DHE 28/.410 sets? One is stamped "00", the other is not stamped. Yet other 28/.410 sets that we have seen previously have been stamped 0000.

[John Dallas]

I did not. The man who had them on his table was pushing me very hard, and At that point I didn't want to do any thing to encourage him. BTW, he was probably within 10 feet of the gentleman(?) who discharged his pistol earlier in the day

[Greg Baehman]

Maybe my post wasn't clear John, the first two pics show the lugs of the two 28/.410 Repros that you had seen at the OGCA Show, the third pic is of the lugs of how we have also seen them stamped. All three pics are .410 barrel sets designed to fit 00-framed Repros.

[Mike Franzen]

BTW, he was probably within 10 feet of the gentleman(?) who discharged his pistol earlier in the day

I hadn't heard of this. I'm assuming it was an accidental discharge?

[John Dallas]

It was accidental. Apparently he shot a pistol through his hand perhaps taking off his thumb. The bullet then ricocheted off the floor and hit another man in the leg

[Mike Franzen]

Good lord! You would have thought this would have been all over the media portrayed as Man Shoots Himself and Bystander at Gun Show.

[John Dallas]

When the gun went off you never heard 2000 people get so quiet so fast.