tom tutwiler
04-01-2010, 08:21 AM
To show that timing is everything in life. I had posted earlier about the broken part on my lifter and the board was kind of enough to advise I had a broken stirrup link. I had figured that this was certainly beyond my ability to repair because parts for a 130 year old gun are hard to come by. Accordingly, I was prepared to sent the broken lock off to get it back in running order as they say. Also decided there was no chance of getting this fixed in time to tote this beast into the woods during turkey season so there was no real rush.
Decided therefore to troll around for parts, knowing my chances weren't good, but I was in no rush. Wouldn't you know it, less then a week or to after starting to look, the God's of Ebay graced me with the following:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300405111572&ssPageName=STRK:MEWAX:IT
Careful analysis of the pictures of the right lock being sold on Ebay with my non-functioning right lock in hand seemed to indicate a swap of stirrup locks might be possible.
Knew that I would be was taking a chance on it not working, but was hoping this would save a bit of time as compared to sending the current non functioning right lock off for repair and perhaps ending up held hostage by a gunsmith far too busy to tackle my little (or perhaps big if a part had to be made) project.
Placed my bid (actually quite a bit higher then what I got it for) and won the auction. After having the part for a week (or several) I decided to break out the gunsmithing screwdrivers, pliers, wooden mallets, wooden dowels etc. and give it a go.
Took a better part of an hour to complete the task and there were moments when I said a resounding "Oh Crap" (or something a tad more crude), but I struggled through. The result is things are looking good. Everything is back together now and seems to function correctly.
The next step it to actually fire the beast (something I've never done).
I'd like to give the old girl a go at Turkey's in the upcoming season, but I also value my fingers on my left hand a lot. The gun has some pretty significant pitting in both barrels, but it is on a number 3 frame and weighs over ten pounds (10 lb 3 oz).
I've got some of the RST light 1 1/4 oz 2 7/8" loads which I know are loaded light. Those would be my turkey loads, but I also have some of the more modern Winchester Western 2 7/8" 1 5/8 oz loads factory loads that I'm contemplating as a proof load. Figure to shoot one each of the heavy load in each barrel using the Tire and rope trick that I've seen posted elsewhere on these forums and see what happens. I don't think she will blow up or I wouldn't try it, but I guess there always is that chance.
Option 2 for testing is just shoot the lite RST's for testing and hunting.
Appreciate any inputs on my plan.
PS. Thanks to the board members who sent me information on how to take this think apart earlier. I'm too heavy handed to even think about tackling something more difficult then this, but this gun is strictly a shooter.
Decided therefore to troll around for parts, knowing my chances weren't good, but I was in no rush. Wouldn't you know it, less then a week or to after starting to look, the God's of Ebay graced me with the following:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300405111572&ssPageName=STRK:MEWAX:IT
Careful analysis of the pictures of the right lock being sold on Ebay with my non-functioning right lock in hand seemed to indicate a swap of stirrup locks might be possible.
Knew that I would be was taking a chance on it not working, but was hoping this would save a bit of time as compared to sending the current non functioning right lock off for repair and perhaps ending up held hostage by a gunsmith far too busy to tackle my little (or perhaps big if a part had to be made) project.
Placed my bid (actually quite a bit higher then what I got it for) and won the auction. After having the part for a week (or several) I decided to break out the gunsmithing screwdrivers, pliers, wooden mallets, wooden dowels etc. and give it a go.
Took a better part of an hour to complete the task and there were moments when I said a resounding "Oh Crap" (or something a tad more crude), but I struggled through. The result is things are looking good. Everything is back together now and seems to function correctly.
The next step it to actually fire the beast (something I've never done).
I'd like to give the old girl a go at Turkey's in the upcoming season, but I also value my fingers on my left hand a lot. The gun has some pretty significant pitting in both barrels, but it is on a number 3 frame and weighs over ten pounds (10 lb 3 oz).
I've got some of the RST light 1 1/4 oz 2 7/8" loads which I know are loaded light. Those would be my turkey loads, but I also have some of the more modern Winchester Western 2 7/8" 1 5/8 oz loads factory loads that I'm contemplating as a proof load. Figure to shoot one each of the heavy load in each barrel using the Tire and rope trick that I've seen posted elsewhere on these forums and see what happens. I don't think she will blow up or I wouldn't try it, but I guess there always is that chance.
Option 2 for testing is just shoot the lite RST's for testing and hunting.
Appreciate any inputs on my plan.
PS. Thanks to the board members who sent me information on how to take this think apart earlier. I'm too heavy handed to even think about tackling something more difficult then this, but this gun is strictly a shooter.