View Full Version : Turnbull MFG. to Appear on "How It's Made"
Dean Romig
10-15-2014, 07:42 PM
Friday night, Oct. 17, 2014 at 9 PM EST Turnbull MFG. Co. will appear on "How It's Made" television.
Bob Kimble
10-15-2014, 09:03 PM
For those that don't know; How It's Made is on the Science Channel.
Frank Cronin
10-15-2014, 11:17 PM
One of my favorite shows. Thanks Dean. Programmed a reminder on the TV.
wayne goerres
10-16-2014, 12:08 AM
I checked my TV guide and it dos'nt list that program for 9 pm on friday on the science channel. I have Dish network. dose it make a difference.
Bob Kimble
10-16-2014, 12:12 AM
I got an e-mail from Turnbull that lists the source as the Science Channel. Maybe Dish lists it at a different time on the Science Channel.
Bob Kimble
10-16-2014, 12:17 AM
Wayne, I just re-checked the e-mail. It does say it's Eastern Standard Time. I'm not sure where you're located. That may make the difference.
ForrestArmstrong
10-16-2014, 01:12 AM
Doug is currently jeweling and coloring a Gournet repro that belongs to me, maybe we'll get to see it.
Bob Hardison
10-16-2014, 08:55 AM
I have Direct TV and SCI HD is channel 284 on mine. Does not list anything for 9pm on my TV guide but went to Direct online and found it listed (firearms restoration). Have it scheduled. Hope this helps.
Dean: Thanks for the heads up. Bob
Brian Dudley
10-16-2014, 09:28 AM
I read about them appearing on TV in the local paper last week as they are a local business. They also have it on their website. I guess the segment will be following the restoration of a Winchester 86 rifle if I remember correctly.
wayne goerres
10-16-2014, 01:56 PM
I am on eastern standard time. Dish and direct are not the same channels. I will try looking again.
Marc Retallack
10-16-2014, 07:39 PM
Wayne, it's channel 193 on Dish.
Angel Cruz
10-16-2014, 08:00 PM
Thanks Dean!! I love that show.
Dean Freeman
10-16-2014, 08:21 PM
Me too! Thanks Dean, the DVR is locked and loaded.
wayne goerres
10-16-2014, 10:28 PM
Thanks I have found it and set to record it.
ForrestArmstrong
10-16-2014, 10:52 PM
Somebody record it and post on youtube so I can see it.
Robin Lewis
10-17-2014, 10:04 AM
Would u-tube allow that? It should be protected by copyright.
Brian Dudley
10-17-2014, 10:32 PM
I enjoyed the segment on sliding doors.
Seriously though. The segment was very good. I liked the extent that they showed stock making and fitting.
Frank Cronin
10-17-2014, 10:41 PM
I enjoyed it. I was hoping to see some info on case hardening but was skipped over.
Rick Losey
10-17-2014, 10:56 PM
yes- considering it was aimed at a general audience - not too bad
it is too bad they did not spend a couple more minutes on the case colors
Brian Dudley
10-17-2014, 11:29 PM
Case coloring is a closely guarded secret over there.
Dean Romig
10-17-2014, 11:32 PM
Apparently...
Bill Murphy
10-18-2014, 12:40 PM
Not anywhere near long enough. I could watch stuff like that for hours.
Brian Dudley
10-18-2014, 12:42 PM
The segment was longer than the normal ones on the show. They took a commercial break in the middle of it.
ForrestArmstrong
10-20-2014, 10:34 AM
I don't see this program but alot of other videos of Doug Turnbull are posted on youtube
vBulletin® v3.8.4, Copyright ©2000-2025, Jelsoft Enterprises Ltd.