|
 |
 |
|||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||
 |
 |
01-13-2026, 10:14 AM
|
#13 | ||||||
|
Yes, I've tried that. Wrote I did in my post. I can push it up, but it will not lock into place. Spring pushes it back down.
|
||||||
|
|
||||||
 |
 |
 |
|
|
|
01-13-2026, 11:30 AM
|
#14 | ||||||
|
Todd,
Check your PM. I can send you some pictures which may provide some assistance.
__________________
Follow a good dog while carrying a fine shotgun and you will never be uninspired. |
||||||
|
|
|
||||||
|
|
|
|
|
|
01-13-2026, 04:44 PM
|
#15 | ||||||
|
The foot or catch on that ejector hammer may be fouled with hardened residue or it may be broken off.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
|
|
|
01-13-2026, 04:49 PM
|
#16 | ||||||
|
Got it fixed! Thank you Dean Weber. Using a soft chair to sit in, I placed the forend between my legs, used a wooden dowel to press the spring back, then in the front, used a plastic pen tip to push down the pin so it aligned in the down position with the other. Spring stayed locked back, and I was able to assemble the gun again. Once I saw that pin was raised, was a 5 second fix. No vise needed, just a soft chair.
|
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Todd Muirhead For Your Post: |
|
|
|
02-15-2026, 02:53 PM
|
#17 | ||||||
|
I’ve followed Dennis’ thread and opened extractors and installed forend. I’m not able to get the extractors to lock in the closed position. I’ll point out that the extractor tumblers on my forearm are cocked, is this a problem or as it should be. Fearful that my extractor sears are damaged. Anyone have any thoughts or advice.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
02-15-2026, 07:01 PM
|
#18 | ||||||
|
Tom, you're using terms associated with both extractor guns and ejector guns and this makes your question confusing for me.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
|
|
|
02-15-2026, 07:21 PM
|
#19 | ||||||
|
I should have stated the ejector tumblers (hammers) are in the cocked position. I can pull out the extractors to the ejected position and am able to attach the forearm to the barrels. Following Dennis’ thread, I should be able to push the extractors in using a wood dole but the they want lock in place. Am I doing any better with my terminology?
|
||||||
|
|
|
||||||
|
|
|
|
|
|
02-15-2026, 07:46 PM
|
#20 | ||||||
|
I think what I'm understanding Tom is that the ejector hammers in the forend will not stay cocked... Am I right?
The actual ejector rods in the barrels are free floating and they do what the ejector hammers in the forend tell them to do. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
 |
| Tags |
| assembly forend |
|
|
Linear Mode
