Parker two barrelled two ga. set

[Chip Beckford]

Hello, I am new to the forums and am trying to get information on a Parker D2 16 Ga. 28 inch 2 1/2 inch with a second set of barrels 12 Ga, serialed to the gun and marked #2 on barrels and forearm that I acquired several weeks ago. I don't know how rare this is if at all, but want to restore the set. The metal is in good shape and the barrels are in very good shape with good bores on both. The bad news is that the forearms are worn, and someone has modified the butt stock, taken off all the checkering, slimed the stock and it has a repaired crack. I do not think the butt stock is restorable and am wondering if I should just try to find a stock for it or get it re-stocked. It is in the 60xxx serial range and I have sent in a request for a factory letter. According to the serialization book it was made as a D2, 16 Ga. made in 1891 with 28 inch barrels which are there. The second set must have been made later and are also serialed to the gun, 12 Ga. with forearm and 3 inch chambers 30 inches long. It is a cool combination and I would like to restore it and am looking for recommendations. Thanks very much!

Chip Beckford

[Dean Romig]

Chip, it is pretty rare to find a two-barrel, two-gauge set even for a gun that went back subsequent to manufacture for the second set in a different gauge. It will be very interesting to learn what the letter has to say - please share it with us.
BTW, is it a hammer gun or a hammerless? Sounds like it will need a re-stock, especially if it is a hammer gun.
Dean

[Austin W Hogan]

Two of my first Parkers were two barrel set guns. One was bought by accident; a large southern dealer offered an interesting lifter gun in Gun List; I bought it and it arrived with two barrel sets of matching gauge and weight. I later found out that early live bird shooters often used two barrel sets to prevent burning fingers.
The second was found locally, within a few miles of its original buyer's home. It was a two gauge, two steel, two barrel set. It was very interesting and the subject of an article in Parker Pages before 1999. The 10 gauge barrels were Dam 4 and 26 inches, the 12 ga barrels were B4 and 30 inches. It was a combination light 10 and heavy 12. The serialization indicates it is a 26 inch B4.
I tried collecting two barrel sets for a while; I managed to find grades 1,2,3, and 4, and duplicate the grade 2 in lifter action. I never found a top action two barrel set, and the only zero grade was in condition two grades below the bottom.

To be continued

Best, Austin

[Austin W Hogan]

I tried to complete the first reply by editing but it did not take.

I found two match balance two barrel sets. One was a Dam3 with 30 inch ten and twelve gauge barrels that matched weight within two ounces, and balance within my ability to measure. This gun was returned to Parker several times for repairs, restock and rebrown, but there are no entries that show both barrel sets.

The second is a Dam 2 twelve gauge with 30 inch waterfowl barrels and 26 inch upland barrels. This two frame gun weighs less than 7 pounds with its upland barrels, and more than 8 pounds with the 30 inch barrels. It is thoroughly specified and occupies a quarter page in the order book. Both barrel sets are specified to be chambered 2 7/8 inch.

I really learned a lot about Parker gun fitting from these two barrel sets. It appears that Parkers' fitters could achieve two barrel set balance match with almost any gauge/length combination by adjusting the "swamp" between breech and fore end tip.

To be continued again

Best, Austin

[Austin W Hogan]

Two barrel set gun collecting is a pretty advanced notch (or nich) in Parker collecting. I ceased chasing two barrel set guns because it required one to accept a pretty significant reduction in condition to obtain them. I have found a couple more interesting two barrel sets in decent condition in the last ten years, but they are seldom seen.

Analyzing Charlie Price's Serialization shows these two barrel sets in the 55000 - 70000
serial range ( ie early hammerless plus exposed hammer)
59 Twelve ga hammerless
5 Sixteen ga Hammerless
4 Twelve ga top action
0 Sixteen ga top action
This totals 68 two barrel sets among 15000 serial numbers, or 5 two barrel sets per 1000 guns. Note that the format used in the Serialization does not allow two gauge, two length or two steel two barrel sets to be identified. Also note that the great preponderance of Parker guns are in Grades 0,1,and 2 which are often missing from the serialization. It would seem that considerable knowledge or perhaps a seance with Mr King,is required to identify a two barrel set that left the factory in that form from this era.

Conversely, replacement Parker barrels were not available from an equivalent of NAPA at this time. A set of Parker barrels required a rib cut and roll marked on Parker's tooling, even if barrels from another supplier were used to make the set. Otherwise,a second set of barrels required breaking another Parker.
It is known that Parker and Remington supplied whole guns in unfinished form to custom gunsmiths for finishing. Parker may have sold barrel sets as well. Is it possible to identify file strokes made somewhere other than Meriden in fitting the replacement barrels?

Best, Austin

[Researcher]

Some years ago I picked up this well used 1889-vintage heavy 2-frame Damascus barrel 12-gauge, that was back to Meriden some time after 1918 for a set of 32-inch Vulcan Steel, 3-inch chambered, 20-gauge barrels with forearm. The 12-gauge Damascus barrels are very thick and straight with little or no swamp and the gun weighs just over nine pounds with them in place. The 20-gauge barrels swamp a lot and the gun weighs 8 pounds 4.5 ounces with them in place. I displayed this gun at The Vintage Cup at Sandanona in 2005, and also had it with me and showed it around some at Pintail Point in 2008, though I was working the A.H. Fox Collectors booth then.

[ED J, MORGAN]

THE 2010 RAFFLE GUN a GHE is a two barrel set.

[C grade]

Austin
Thank you. I had no idea two barrel sets were that unusual. I shoot a nice DH 12/12 with a 30" Mod/full and a 28' imp/mod. I also have a CHE 20/20 28" skeet /skeet & 28" mod/full. I treasure those guns and now even more so.
Thanks
David

[DDowner]

With only a 164 fluid steel 20 ga. CH's I would think yours is very uncommon David.

[Chip Beckford]

Hi Dean, I should have mentioned it, it is a hammerless. I will try to get some pictures over the holidays, Thanks for the note, Chip