|
 |
 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
06-30-2010, 06:41 PM
|
#23 | |||||||
|
Quote:
Wow! I've never heard of that before. Have you ever seen another in any gauge that was made that way? I've seen a couple of early Parkers with gas venting recesses in the standing breech and escape holes. . Last edited by Dean Romig; 06-30-2010 at 07:12 PM.. |
|||||||
|
|
|||||||
 |
 |
 |
|
|
|
06-30-2010, 06:42 PM
|
#24 | ||||||
|
Bill Zachow, it is very interesting that you mention a hammer gun built on a #5 frame, but hammerless eight gauges seem to be limited to #6 frames. In fact, there seem to be no #4 or #5 hammerless frames in any gauge that have surfaced. I have measured the eight gauge shell against the existing frame sizes and have determined that an eight gauge #3 frame hammerless gun can be built, but no one has come forward with one built at the Parker Brothers factory so far.
|
||||||
|
|
|
||||||
|
|
|
|
Frame Size | |
|
07-01-2010, 07:38 AM
|
#25 | ||||||
|
Frame Size
I think that the Remington Frame information came from a parts list of 1950's vintage. The frame info was to be used when ordering parts.
Best, Austin |
||||||
|
|
|
||||||
|
|
|
|
|
|
07-02-2010, 09:54 AM
|
#26 | ||||||
|
Austin, if I remember correctly, there has been quite a lot of research published in the Parker Pages about the half frame 12's. There was that article and several others by Parker experts who carefully went through the PGCA records. Great research and fine articles. There was another article specifically dealing with average weights if anyone is interested.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
07-02-2010, 10:13 AM
|
#27 | ||||||
|
And it seems every time we discuss it here another little tidbit of 1/2 frame information surfaces.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
07-02-2010, 11:12 AM
|
#28 | ||||||
|
Well we don't want to get into the black hole of forgetting about what has been already written about the subject in the Parker Pages.
|
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Bruce Day For Your Post: |
|
|
|
02-10-2022, 09:36 PM
|
#29 | ||||||
|
I just came across the 1/2 Frame blueprint.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following 11 Users Say Thank You to Dean Romig For Your Post: |
|
|
|
02-11-2022, 02:55 AM
|
#30 | ||||||
|
So it appears the designers married a No. 1 standing breech to a No. 0 lower frame and components except for an offset on the hammer noses to match the No. 1 pin spacing.
The lightning cuts on the water table are like the No. 00 frame. Very interesting, and I wish that the times had not cut the production short. I would love to own one. Last edited by David Noble; 02-11-2022 at 02:56 AM.. Reason: Spelling error. |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to David Noble For Your Post: |
 |
|
|
The reason I remembered is that I helped just a wee bit on that article with Craig....
Linear Mode
