|
10-23-2014, 06:42 PM | #33 | ||||||
|
Gary,
Are you getting in to many birds? I'm heading for Potter Monday morning. I only started hunting Potter for grouse in the last couple years. Last season, my scouting over the previous years really started to pay off. I'm still learning the area but I am really looking forward to next week. Best of the luck at the sale... Hope Chuck doesn't outbid you Marcus
__________________
"Nowadays, when one is forced to cross the country in a few hours and drink three-day-old beer, ain't it a pleasure to know, as I'm sure you do, that good friends, good bourbon, and good tobacco are slowly made." Gene Hill www.cure.org |
||||||
10-23-2014, 07:45 PM | #34 | ||||||
|
Marc, so far the birds have been hard to find but there is an abundance of food and cover. It will get better later, I hope.
Chuck, I heard we are in for a noreaster on Sunday with a foot of snow predicted! Might be a tough drive. |
||||||
The Following User Says Thank You to Gary Laudermilch For Your Post: |
10-25-2014, 09:57 AM | #35 | ||||||
|
Thanks Gary
__________________
"Nowadays, when one is forced to cross the country in a few hours and drink three-day-old beer, ain't it a pleasure to know, as I'm sure you do, that good friends, good bourbon, and good tobacco are slowly made." Gene Hill www.cure.org |
||||||
10-25-2014, 04:18 PM | #36 | ||||||
|
Ok, guys I took a look at this Parker lifter. I don't know quite where to begin but you can bet your bottom dollar that this was a high grade Parker. What I saw and keep in mind that I am not very knowledable about these older guns:
The action is beautiful and in very good shape except for the cracks on both sides. It is a square frame, ie no radius where the water table meets the breech face. I took a dental pick along to see if I could detect how deep the crack was. I was unable to detect a crack on the inside in the locking bolt slot. The barrels seem to lock up very nicely, actually much better than I expected. However, it is severly off face probably due to the crack and being out of square. That is the big question. Can it be repaired? The butt stock is pretty rough. The repair patch is only on one side so you can see the break on the other. It looks to be pretty much straight across rather than running with the grain. The reinforced side is definitely missing some wood especially where the lock plate abutts and the plate has been inlet into the wood. Who knows what is under the repair plate. The skeleton butt plate is there. The wood is of high quality - very nice figure. The forend is quite good with a lever latch and fits quite well. All serial numbers match. There is a large U on the water table with another set of 3 digit numbers that do not match the serial number. The barrel lug has a large 2 with a smaller 0 above it, presumably indicating a 2 size frame. The barrels measure just a smidge over 27 inches. The barrels are not touching but are no further apart than my uncut V grade. The keels are quite obvious and when I scratched them appear to be brass. I am kind of thinking they are original length. There is some outside rust and relatively minor pitting and mostly near the muzzle end. The bores look quite good. Frosting in the first one third and one obvious pit in each about mid way but do not look to be too bad. Nice looking damascus fine pattern under the forend. I saw much more than I can explain here. I'm going to the auction and we'll see where the bidding goes. It would be a shame to give up on this grand old girl. |
||||||
10-25-2014, 05:15 PM | #37 | |||||||
|
Quote:
This frame crack in the early dollar grade lifters is not at all uncommon, and has likely been seen, repaired, and returned, with a radius intersection, by better gunsmiths. In my opinion, this should in no way scare off a serious collector. The investment will not be an inconsequential amount, but the gun warrants it, and it will be money well spent. The breech face to water table is never truly square. If it were, the gun won't open. The longer the water table, the closer to 90 degrees they get, and vice verse. Without a research letter, you won't know for certain what the original barrel length was. A very beautiful Grade 3, 12ga. Lifter followed me home today, and I have long been a lover of shooting these beautifully balanced guns |
|||||||
10-25-2014, 05:57 PM | #38 | ||||||
|
Thanks of the comment Edgar. The serial number is 13334. I intend to see what I can do.
|
||||||
10-26-2014, 05:09 AM | #39 | |||||||
|
Quote:
The SN of the subject gun is right about where I expected. There was some over lap between the early frame, without the reinforcing rib and sharp corner, and the improved one. See TPS, Page 102, and pictures, page 104. There were many other changes in addition to this one, but it was all in the high 13K to 16 K range. |
|||||||
10-26-2014, 11:51 AM | #40 | ||||||
|
I'm not a gunsmith, but just thinking this repair through, this is how I envision it going;
(After taking carefull measurements of the standing breech to water table angle) It would be necessary to chase the cut, with a cutting wheel to a little bit beyond the depth of the crack. Tig weld crack, re-cut affected engraving, and then refinish. If the standing breech angle had been opened by the crack, a jig would be necessary to close the angle a bit. If the gun could be had for the right price, and I had the budget, I would not be afraid of this project. |
||||||
|
|