![]() |
![]() |
![]() |
|||||||||||||||||||||||||||||||||||||||
|
![]() |
![]() |
![]() |
#3 | ||||||
|
![]()
PB has completely vanished from my part of the planet. I'm looking for possible loads for 2 1/2" 20ga. using either Universal or International Clays and SG20 wads, got lots of both. I've had real good success feeding my short 16s International and would sure like to get it working with a mild (under 8K) +/-1150 fps 7/8 oz load for the 20s. I'm using Cheddite hulls. Has anyone any experience in this direction?
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#4 | ||||||
|
![]()
I use one piece AA hulls with a Win 209 primer, Winchester Double A wads, 14 grains of 20/28 powder and 7/8 oz. of shot. I use this load in my newer steel barreled Trojan and VH but use the same load but with 13.3 grains of 20/28 in my older Damascus DH 20.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to Dean Romig For Your Post: |
![]() |
![]() |
![]() |
#5 | ||||||
|
![]()
Couldn't find any loads using the SG20 wad listed in my 20 ga spreadsheets.
I use Claybuster 1078 and 1075--they are Win AA clones and a bag of 500 is ususally around $10. I have used this load with Unique: Ched 2 1/2"/ win or ched 209 primer/ Unique 16gr/CB1078/ 1186fps@ 7200 psi. I have used this load in 2 3/4" cheddite, but may fit in a 2 1/2"--definitely will if dropped to 3/4 oz load: Universal 17gr/ Win or ched 209 primer/CB 1078/ 1197 fps/ 7800 psi
__________________
"How kind it is that most of us will never know when we have fired our last shot"--Nash Buckingham |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to Harold Lee Pickens For Your Post: |
![]() |
![]() |
![]() |
#6 | ||||||
|
![]()
Here's a load I have used and recoil was mild.I have not had it tested.Im sure I found this listed here in the reloading forum.New Fiocchi hulls cut to 2 1/2 inch,16 grs.Universal,SG20M wad,8 fold crimp.It was listed as having 8500 PSI,and 1200 FPS.Another load with same hull and 3/4 oz.of shot,14 grs.20/28,CB1075 wad,8 fold crimp,listed as having 7500 PSI,at 1200 FPS.I would think you could sub a Cheddite hull and primer as both are straight walled hulls and very similar.Do this at your own risk as I have not had these tested.The load with 20/28 was a little smoky.The load with Universal was clean.These were fired in a Trojan with steel barrels.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to Jeff Sweeter For Your Post: |
![]() |
![]() |
![]() |
#7 | ||||||
|
![]()
Just made a correction.Didnt have the grains listed for the 20/28.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#8 | ||||||
|
![]()
[QUOTE=Dean Romig;299644]I use one piece AA hulls with a Win 209 primer, Winchester Double A wads, 14 grains of 20/28 powder and 7/8 oz. of shot. I use this load in my newer steel barreled Trojan and VH but use the same load but with 13.3 grains of 20/28 in my older Damascus
Dean, do you know the psi/fps on this? I'd like to try it using 3/4 ounce of shot. Thx Chris |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to Chris Robenalt For Your Post: |
![]() |
![]() |
![]() |
#9 | ||||||
|
![]()
Hey Chris, in Win AA With W209 primer and CB1075 wad-(chartruse):3/4 oz
14.5 gr 20/28 1200 fps @ 7200 psi 15.5 gr 20/28 1250 fps @ 7900 psi So 13.3 gr 20/28 should be very mild, and I'm guessing around 1100 fps and in the 6000's psi. range I usually load the 14.5 gr load for both my steel and damascus 20's. It is a nice load.
__________________
"How kind it is that most of us will never know when we have fired our last shot"--Nash Buckingham |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to Harold Lee Pickens For Your Post: |
![]() |
![]() |
![]() |
#10 | ||||||
|
![]()
Hey, thanks Harold, I have all the components! I'll play with the powder amount....
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|
|