|
 |
 |
|||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||
 |
 |
09-10-2023, 08:47 PM
|
#3 | ||||||
|
What are the measurements of the barrel?
__________________
B. Dudley |
||||||
|
|
||||||
 |
 |
 |
| The Following 2 Users Say Thank You to Brian Dudley For Your Post: |
|
|
|
09-11-2023, 10:39 AM
|
#4 | ||||||
|
Dudley, I don't remember exactly, I just remember he said he wouldn't even suggest rst loads out of the right barrel.
__________________
" My problem is I want to follow Jesus and slap people too" |
||||||
|
|
|
||||||
|
|
|
|
reassembly DHE | |
|
09-11-2023, 11:18 AM
|
#5 | ||||||
|
reassembly DHE
I disassembled my DHE for some stock work . Upon reassembly I cannot get forearm back on. Everything else seems right ? Help
|
||||||
|
|
|
||||||
|
|
|
|
|
|
09-11-2023, 03:30 PM
|
#6 | ||||||
|
It’s advisable to start a new thread with your new topic. The home page has lots of helpful information, such as pertaining to your inquiry. Easy fix:
__________________
Phlebas the Phoenician, a fortnight dead, forgot the cry of gulls, and the deep sea swell and the profit and loss. A current under sea picked his bones in whispers. As he rose and fell he passed the stages of his age and youth entering the whirlpool. T.S. Eliot |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Bruce P Bruner For Your Post: |
|
|
|
09-11-2023, 04:01 PM
|
#7 | ||||||
|
What would a minimum wall thickness in front of the chambers be for a 12 gauge, any frame size?
|
||||||
|
|
|
||||||
|
|
|
|
|
|
09-11-2023, 09:17 PM
|
#8 | ||||||
|
My WAG is about 0.0115" as a minimum... or should I say that for my own personally safety I wouldn't shoot an old sxs that had less than 0.0110" at the juncture of the chamber and the beginning of the forcing cone.
I have a Damascus 0-frame 16 gauge GHE that Oscar Gaddy measured at 0.0063" and wrote to me that it "is probably safe to shoot with pressures of less than 7,500 psi." .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
|
|
|
09-11-2023, 10:09 PM
|
#9 | ||||||
|
I ain't 100% sure but if I remember I think.0030. It had been refinished and he said they took too much out while doing so. I may wind up just getting a set of tubes from briley, but I would love to find a set of barrels and have them fitted.
__________________
" My problem is I want to follow Jesus and slap people too" |
||||||
|
|
|
||||||
|
|
|
|
|
|
09-11-2023, 10:48 PM
|
#10 | ||||||
|
Well, without knowing what the measurements were, we cannot exactly advise on it. Keep an eye out for barrels and hope they can be fitted. Best of luck.
Thicknesses at the front of the forcing cones will usually be in the .090” to .110” area on 12g guns. I have seen as low as .080” in various gauges and they were perfectly shootable guns.
__________________
B. Dudley |
||||||
|
|
|
||||||
|
|
|
| The Following 4 Users Say Thank You to Brian Dudley For Your Post: |
 |
|
|
Linear Mode
