Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions Damascus Barrels & Steel

Notices

Reply
Thread Tools Display Modes
Damascus in my future
Unread 07-26-2020, 11:54 AM   #1
Member
Keith Doty
PGCA Member
 
Keith Doty's Avatar

Member Info
 
Join Date: Dec 2018
Posts: 570
Thanks: 545
Thanked 718 Times in 293 Posts

Default Damascus in my future

After an youth spent reading the warning on every box of shells a paper route income could purchase I had always relegated anything with Damascus barrels to wall hanger status. After exposure to current company I find many are regularly shooting (and surviving) some really beautiful guns I had always been scared of. I fear that my next gun may well be a Damascus Parker!
Problem: I know little or nothing about them. Obviously whatever I purchase I want to shoot with confidence and know the barrel condition is everything in that regard. Is there a MWT rule of thumb that differs from steel barrels, what's considered safe? What is considered "safe" pressure range per gauge? Are there things to avoid unique to this type of barrel?
My understanding is Kirk Merrington (sp) here in Texas is one of the experts highly thought of. Others in this region?
I'd truly like the learning experience to be as painless as possible, DON'T want to end up with a beautiful wall decoration! Any help here is appreciated.
Keith Doty is offline   Reply With Quote
The Following User Says Thank You to Keith Doty For Your Post:
Unread 07-26-2020, 12:32 PM   #2
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 31,557
Thanks: 35,430
Thanked 33,039 Times in 12,321 Posts

Default

Damascus barrels share about the same minimum wall thickness preference as the fluid steel barrels of the day and the commonly accepted MWT for both is about .025” for the front half of the barrel and about .090” or better at the juncture of the chamber and the forcing cones.

Others’ opinions may vary of course.

Preferred pressures are usually below 8,500 psi but I prefer even less for my purposes.



.
__________________
"I'm a Setter man.
Not because I think they're better than the other breeds,
but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture."

George King, "That's Ruff", 2010 - a timeless classic.
Dean Romig is offline   Reply With Quote
The Following 2 Users Say Thank You to Dean Romig For Your Post:
Unread 07-26-2020, 12:49 PM   #3
Member
Drew Hause
Forum Associate
 
Drew Hause's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,084
Thanks: 323
Thanked 3,761 Times in 1,245 Posts

Default

Keith: wall thickness and other damascus relevant questions are addressed in the FAQs
http://parkerguns.org/

and
https://docs.google.com/document/d/1...vwLYc-kGA/edit

https://docs.google.com/document/d/1...hIiY62Hx4/edit

Last edited by Drew Hause; 07-26-2020 at 01:56 PM..
Drew Hause is offline   Reply With Quote
The Following 3 Users Say Thank You to Drew Hause For Your Post:
Visit Drew Hause's homepage!
Unread 07-26-2020, 01:33 PM   #4
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 31,557
Thanks: 35,430
Thanked 33,039 Times in 12,321 Posts

Default

Drew’s recommended readings are well worth the time invested in thoroughly reading them.





.
__________________
"I'm a Setter man.
Not because I think they're better than the other breeds,
but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture."

George King, "That's Ruff", 2010 - a timeless classic.
Dean Romig is offline   Reply With Quote
The Following User Says Thank You to Dean Romig For Your Post:
Unread 07-27-2020, 12:00 PM   #5
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,521
Thanks: 6,118
Thanked 8,780 Times in 4,716 Posts

Default

A Manson wall thickness gauge, properly used, will be much cheaper than a trip to a gunsmith, and yield the same results.
Bill Murphy is offline   Reply With Quote
The Following User Says Thank You to Bill Murphy For Your Post:
Unread 07-30-2020, 11:31 AM   #6
Member
Bruce Day
PGCA Lifetime
Member
 
Bruce Day's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 4,993
Thanks: 552
Thanked 15,605 Times in 2,666 Posts

Default

I have Parkers , Lefevers and a Colt with half fluid steel and composite barrels. I do not differentiate between the two barrel types for cartridge loads . A number 2 frame 12 ga is the most common type of a Parker that is readily available; these guns were made to shoot stout loads up to 1 1/4 oz and 3 1/4 drams. While I do not like that heavy a load, I am confident the gun will safely shoot it if I choose to.
Bruce Day is offline   Reply With Quote
The Following 2 Users Say Thank You to Bruce Day For Your Post:
Unread 07-30-2020, 11:48 AM   #7
Member
Drew Hause
Forum Associate
 
Drew Hause's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,084
Thanks: 323
Thanked 3,761 Times in 1,245 Posts

Default

We're repeating ourselves, but there's not much else we can do, at least in Phoenix right now

It is now well established that Parker and the other U.S. makers proved their barrels, as are the loads and pressures for which they were designed. Scroll down about 1/4 for Parker's proof pressures
https://docs.google.com/document/d/1...UOZEFU/preview

The problem of course is that very few now 120 year old guns/barrels have not been subject to abuse or modification at some point.
Looking down the bore with a scope, and measuring the wall thickness, is simply due diligence and good sense, and might protect our shooting companions, or kids & grandkids, from injury, which should make the effort worth it.
Drew Hause is offline   Reply With Quote
The Following 3 Users Say Thank You to Drew Hause For Your Post:
Visit Drew Hause's homepage!
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:23 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.