![]() |
![]() |
![]() |
|||||||||||||||||||||||||||||||||||||||
|
![]() |
![]() |
![]() |
#3 | ||||||
|
![]()
ALL Parker bores were honed after boring at the factory.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to Dean Romig For Your Post: |
![]() |
Overbore | ![]() |
![]() |
#4 | ||||||
|
![]()
Most, but not all. That's the reason for the question.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#5 | ||||||
|
![]()
No entirely correct.
Plenty of Parker guns were overbored when built. Especially prior to 1900, I have measured some 12g. barrels with bore diameter creeping up into the 10g. range and the barrels were completely original. On the Super Fox overboring was one of the keys to its long range performance. But yes, bores can be honed out after the fact to clean up pitting or damage, which can increase the bore diameter slightly. But just because a bore is oversized, does not mean that it must have been messed with after the fact.
__________________
B. Dudley |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 6 Users Say Thank You to Brian Dudley For Your Post: |
![]() |
![]() |
![]() |
#6 | ||||||
|
![]()
My 1918 SC and 1934 SC both had standard bores with .040" choke constrictions
__________________
http://sites.google.com/a/damascuskn...e.com/www/home |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to Drew Hause For Your Post: |
![]() |
Overbore | ![]() |
![]() |
#7 | ||||||
|
![]()
Thank you Drew. That is the kind of information I was looking for. Actual bore measurements of SBTs to try to understand how many might be overbored.
Just trying to understand if it might have been something Parker did as a standard offering. And thank you Harry for stating the obvious. |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#8 | ||||||
|
![]()
The SBT I currently own has:
.742" bore .703" choke .039" constriction Ser. # 223403 JSH |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following 2 Users Say Thank You to J. Scott Hanes For Your Post: |
![]() |
![]() |
![]() |
#9 | ||||||
|
![]()
Was wiping down a few today from the safe and measured bores.
SN 238162 SC 34" bore .730 Choke.036 SN 225127 SC 34" bore .731 Choke .031(Extended Forcing Cones) SN 232323 SC 32" bore .732 Choke .033 SN 206107 SC 32" bore .729 Choke .036 SN 190625 SA1 32"bore .742 Choke .044 (Upgrade by Delgrego and Runge) I feel 238162,232323and 206107 have untouched bores. 225127 has original bore and choke but forcing cones have been extended. 190625 has been upgraded (1972) and most likely had bores polished. Hope this helps Paul ![]() |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to PAUL PLUNKETT III For Your Post: |
![]() |
Parker SB Trap bores and chokes | ![]() |
![]() |
#10 | ||||||
|
![]()
Thank you very much Paul. That is exactly the type of information I was hoping to receive. Sounds like you have a very nice collections of SBTs!
Happy Thanksgiving - Scott |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|
|