Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums General Parker Discussions

Notices

Reply
Thread Tools Display Modes
What kind of ugly on a Parker do you hate??
Unread 11-20-2023, 03:28 PM   #1
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,537
Thanks: 2,954
Thanked 10,430 Times in 1,647 Posts

Default What kind of ugly on a Parker do you hate??

I like solid Parkers that show honest hunting wear. What drives me nuts are ugly damascus barrels. I have no issue with properly restored damascus barrels. How about you??
Craig Larter is offline   Reply With Quote
The Following User Says Thank You to Craig Larter For Your Post:
Unread 11-20-2023, 04:14 PM   #2
Member
edgarspencer
PGCA Member
 
edgarspencer's Avatar

Member Info
 
Join Date: Sep 2011
Posts: 6,100
Thanks: 2,946
Thanked 11,547 Times in 3,106 Posts

Default

I much prefer a D4 pattern over Bernard.
edgarspencer is offline   Reply With Quote
Unread 11-20-2023, 04:20 PM   #3
Member
OH Osthaus
PGCA Lifetime
Member
 
Rick Losey's Avatar

Member Info
 
Join Date: Jul 2010
Posts: 7,808
Thanks: 1,646
Thanked 8,157 Times in 3,260 Posts

Default

ugly? I have a project PH that has gold gilding on part of the fore-end metal

worse yet is that the fore-end is not serial numbered to the gun- so no telling how bad the whole gun it came from would have looked pimp'ed up
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
Rick Losey is offline   Reply With Quote
The Following User Says Thank You to Rick Losey For Your Post:
Unread 11-20-2023, 04:23 PM   #4
Member
Craig Budgeon
PGCA Member

Member Info
 
Join Date: Jan 2016
Posts: 479
Thanks: 123
Thanked 341 Times in 207 Posts

Default

I can stand a lot of ugly on a hunting gun as long as it shoots where I point it. Guns who reside in the safe and are show and tell peices better look good and not embarass me. Since I do much of my own work I probably don"t wait as long as most to address an iissue. Finally, I once saw an american double that had the wood refiniished and the receiver recased, the work was high quality, however, the damascus barrels were left with there original finish. In my opinion the gun deserved a place in the back of the gun safe where I didn't have to look at it.
Craig Budgeon is offline   Reply With Quote
The Following 2 Users Say Thank You to Craig Budgeon For Your Post:
Unread 11-20-2023, 07:25 PM   #5
Member
Kevin McCormack
PGCA Lifetime
Member

Member Info
 
Join Date: Jun 2009
Posts: 2,018
Thanks: 1,237
Thanked 3,619 Times in 1,024 Posts

Default

My all time favorite is the Dremel-pencilled SSN diagonally across the floorplate, especially on smallbores!
Kevin McCormack is offline   Reply With Quote
The Following 6 Users Say Thank You to Kevin McCormack For Your Post:
Unread 11-20-2023, 07:51 PM   #6
Member
David Noble
PGCA Member
 
David Noble's Avatar

Member Info
 
Join Date: Nov 2010
Posts: 918
Thanks: 1,319
Thanked 1,095 Times in 388 Posts

Default

I once had a CHE 12ga 30" barreled gun that someone had used a torch to color the receiver. It wasn't too bad looking actually. What made me sell the gun was a large duck flying across the bottom of the floorplate with a big silly smile on it's beak. It's head was angled slightly enough that it looked like the duck was glancing back and laughing at me after I had missed the shot. I quickly grew tired of the humiliation and sold it.
David Noble is offline   Reply With Quote
The Following 7 Users Say Thank You to David Noble For Your Post:
Unread 11-20-2023, 08:11 PM   #7
Member
chris dawe
PGCA Member
 
chris dawe's Avatar

Member Info
 
Join Date: Aug 2010
Posts: 1,173
Thanks: 2,581
Thanked 2,784 Times in 602 Posts

Default

Effed up screws,hands down
chris dawe is offline   Reply With Quote
Unread 11-20-2023, 08:28 PM   #8
Member
Researcher
PGCA Lifetime
Member
 
Dave Noreen's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 3,608
Thanks: 1,632
Thanked 7,835 Times in 2,362 Posts

Default

Hot blued barrels.
Dave Noreen is offline   Reply With Quote
The Following 6 Users Say Thank You to Dave Noreen For Your Post:
Unread 11-20-2023, 08:34 PM   #9
Member
Chris T.
PGCA Member

Member Info
 
Join Date: Jun 2009
Posts: 852
Thanks: 479
Thanked 548 Times in 260 Posts

Default

Quote:
Originally Posted by chris dawe View Post
Effed up screws,hands down
Definitely bad screws. Honest wear and tear don't bother me in the least, but bad screws and scars from grandpa's Stanly screwdrivers make me cringe.
Chris Travinski is offline   Reply With Quote
The Following 5 Users Say Thank You to Chris Travinski For Your Post:
Unread 11-20-2023, 08:41 PM   #10
Member
mobirdhunter
PGCA Lifetime
Member
 
Garry L Gordon's Avatar

Member Info
 
Join Date: Jul 2013
Posts: 4,702
Thanks: 13,260
Thanked 9,596 Times in 3,087 Posts

Default

Non-original beavertails.
__________________
“Every day I wonder how many things I am dead wrong about.”
― Jim Harrison
"'I promise you,' he said, 'on my word of honor, I won't die on the opening of the bird season.'" -- Robert Ruark (from The Old Man and the Boy)
Garry L Gordon is offline   Reply With Quote
The Following 7 Users Say Thank You to Garry L Gordon For Your Post:
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:27 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.