|
 |
 |
|||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||
 |
 |
01-28-2021, 05:14 AM
|
#3 | ||||||
|
Reggie can you post pictures of an example?
|
||||||
|
|
||||||
 |
 |
 |
| The Following User Says Thank You to Mike Franzen For Your Post: |
|
|
|
01-28-2021, 06:25 AM
|
#4 | ||||||
|
Twice I have seen some, what I thought was strange and very questionable, rippling along the barrel exterior, especially visible when holding up to a light source and sighting along the outside surface.
This effect was caused by some ham-handed shade-tree ‘gunsmith’ eremoving rust by running the barrels ACROSS their length against a wire wheel. Sometimes hard to catch unless you sight down the length as I have described. One of these guns was a C grade Fox and the other was a grade 2 Ithaca. .
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
||||||
|
|
|
| The Following User Says Thank You to Dean Romig For Your Post: |
|
|
|
01-28-2021, 06:42 AM
|
#5 | ||||||
|
Maybe the term is riffling or rippling. I will try to get a picture. It is not easy to see. It is on the bottom of one barrel only and it is not visible looking into the bores. I googled it and read some discussions on other boards which were not much help. Some said it was due to poor re-finishing and some said they had seen factory barrels with it and it was a result of not being properly finished at the factory. These discussions were not about Parker guns in particular.
__________________
"A man who carries a cat by the tail learns something he can learn in no other way." |
||||||
|
|
|
||||||
|
|
|
|
|
|
01-28-2021, 09:19 AM
|
#6 | ||||||
|
Reggie is right. "Rivveling" is a series of small, shallow waves/ripples in the barrel interior or exterior. They are an aftermarket syndrome caused by a minor barrel obstruction or overloaded cartridges. They can be removed, but with resultant thinning of the barrel wall. In many cases they are cosmetically objectionable, but not too dangerous. Evaluation by a competent double gunsmith is best.
|
||||||
|
|
|
||||||
|
|
|
| The Following 4 Users Say Thank You to John Campbell For Your Post: |
|
|
|
01-28-2021, 10:15 AM
|
#7 | ||||||
|
I have seen it a few times, last was on a 16ga DHE in left barrel just before and into the choke .I turned down the gun because of it. I also believe it's caused by a minor barrel obstruction or a overload ,maybe a magnum load or steel.
__________________
" May you build a ladder to the stars climb on every rung and may you stay forever young " Bob Dylan |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to James L. Martin For Your Post: |
|
|
|
01-28-2021, 10:18 AM
|
#8 | ||||||
|
This one is in the mid section of left barrel on the bottom only best I can tell. Maybe because the left barrel has the tighter choke?
__________________
"A man who carries a cat by the tail learns something he can learn in no other way." |
||||||
|
|
|
||||||
|
|
|
|
|
|
01-28-2021, 10:47 AM
|
#9 | ||||||
|
It can also be caused by the use of steel shot in barrels with too tight a choke, especially with large shot sizes, for the loads used.
|
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Kevin McCormack For Your Post: |
|
|
|
01-28-2021, 12:50 PM
|
#10 | ||||||
|
Hard to see in the picture but here goes.
__________________
"A man who carries a cat by the tail learns something he can learn in no other way." |
||||||
|
|
|
||||||
|
|
|
| The Following 4 Users Say Thank You to Reggie Bishop For Your Post: |
 |
|
|
Linear Mode
