Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums Parker Restoration

Notices

Reply
Thread Tools Display Modes
checkering tool(s) for Trojan checkering
Unread 04-29-2016, 08:59 PM   #1
Member
BRDHNTR
PGCA Lifetime
Member

Member Info
 
Join Date: Nov 2012
Posts: 2,564
Thanks: 2,658
Thanked 1,444 Times in 671 Posts

Default checkering tool(s) for Trojan checkering

What checkering tool or tools would one need to re-cut both fore end and wrist checkering on a Trojan (16 ga)?
allen newell is offline   Reply With Quote
Unread 04-29-2016, 09:33 PM   #2
Member
charlie cleveland
PGCA Member

Member Info
 
Join Date: Jul 2009
Posts: 9,619
Thanks: 0
Thanked 4,484 Times in 2,414 Posts

Default

them wood working boys will jump in here shortly...good luck...charlie
charlie cleveland is offline   Reply With Quote
Unread 04-30-2016, 06:34 AM   #3
Member
Dean Romig
PGCA Lifetime
Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 22,204
Thanks: 19,009
Thanked 17,551 Times in 7,104 Posts

Default

Careful Allen - the Trojans were originally checkered in a fairly coarse LPI with flat top diamonds. A used Trojan may appear to have almost worn off checkering but that is often not the case. Look at a high condition original to see what the checkering should look like before starting.






.
__________________
"I'm a Setter man.
Not because I think they're better than the other breeds,
but because I'm a romantic - stuck on tradition - and to me,
a Setter just "belongs" in the grouse picture."

George King, "That's Ruff", 2010 - a timeless classic.
Dean Romig is offline   Reply With Quote
The Following User Says Thank You to Dean Romig For Your Post:
Unread 04-30-2016, 06:48 AM   #4
Member
chris dawe
PGCA Member
 
chris dawe's Avatar

Member Info
 
Join Date: Aug 2010
Posts: 970
Thanks: 2,088
Thanked 2,250 Times in 458 Posts

Default

Im sure others will know better ...but personally I would use a 60 degree single line cutter ,and a viener to finish the edges and bottoms ...take your time with lots of breaks if its your first Allen.
Good luck ,
Chris
chris dawe is offline   Reply With Quote
The Following 5 Users Say Thank You to chris dawe For Your Post:
Unread 04-30-2016, 11:05 AM   #5
Member
Kensal Rise
PGCA Member

Member Info
 
Join Date: Sep 2011
Posts: 1,467
Thanks: 239
Thanked 1,808 Times in 710 Posts

Default

[QUOTE=chris dawe;194238 ...take your time with lots of breaks if its your first Allen.
[/QUOTE]

Chris is quite right. And perhaps not right enough. If you've never done chequering before, and this is your gun, I'd think twice about doing it at all. Frankly, the odds are about 10-to-1 that you will make a very bad mistake.

A pro like Chris can do the job perfectly. And probably within your budget.
John Campbell is offline   Reply With Quote
The Following 3 Users Say Thank You to John Campbell For Your Post:
Unread 04-30-2016, 11:19 AM   #6
Member
chris dawe
PGCA Member
 
chris dawe's Avatar

Member Info
 
Join Date: Aug 2010
Posts: 970
Thanks: 2,088
Thanked 2,250 Times in 458 Posts

Default

Quote:
Originally Posted by John Campbell View Post
Chris is quite right. And perhaps not right enough. If you've never done chequering before, and this is your gun, I'd think twice about doing it at all. Frankly, the odds are about 10-to-1 that you will make a very bad mistake.

A pro like Chris can do the job perfectly. And probably within your budget.
Very kind of you to say John ,thank you .
Chris
chris dawe is offline   Reply With Quote
Unread 04-30-2016, 11:38 AM   #7
Member
BRDHNTR
PGCA Lifetime
Member

Member Info
 
Join Date: Nov 2012
Posts: 2,564
Thanks: 2,658
Thanked 1,444 Times in 671 Posts

Default

Thanks Gents all. Looking at a 16 Trojan w/dolls head that one of our local shops has up for short money. Gun is tight, no dents, bluing mostly gone but no dings. Stock is quite dark and checkering is faint to the eye but could be that stock after de-oiling will show more checkering. forend is in same condition. 26 inch barrels too. good little grouse and woodcock gun after its cleaned up.
allen newell is offline   Reply With Quote
The Following User Says Thank You to allen newell For Your Post:
Unread 04-30-2016, 08:26 PM   #8
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 7,126
Thanks: 251
Thanked 8,356 Times in 2,472 Posts

Default

If the lines are left and have some feel to them, a 60 degree cutter is all you need to deepen the lines. Cutting the proper borders requires a separate concave cutting tool in combination with others. Proper border work on a Parker makes all the difference between just checkeing it and checkering it right.

However, heed others advice and proceed with caution if you are considering doing it yourself. Since you do not have tools, i take it you have little to no experience cutting or recutting checkering. Not that anyone cant do it, but some just cannot do it. Why try and find out when you can spend relatively short money and have the work done right.


If you insist on trying your hand, pick up a Gunline starter set in 16 lines per inch and spend some time scratching at some junk stocks before trying on something that you want to let out in public.
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
Visit Brian Dudley's homepage!
Unread 04-30-2016, 08:54 PM   #9
Member
Thomas Garver
Forum Associate

Member Info
 
Join Date: Nov 2010
Posts: 48
Thanks: 9
Thanked 13 Times in 10 Posts

Default

Allen, like you I wanted to give a try at checkering. The first thing that I determined was the lines per inch on the stock. Then I trolled the internet and bought a starter set of Dem-Bart tools. There are lots of sets out there in number of tools and prices. My starter stock was 16LPI and I had trouble finding it. Use the guide that comes in the kit and start on a piece of soft wood to get the feel of cutting before moving on. Start from a baseline and continue to work from it. Buy additional heads so that you have a sharp tool, start slow and don't try to cut the line the complete depth on one pass. I take plenty of breaks because when my hand gets tired I tend to make mistakes. The work that you see posted by others here is not done in 5 minutes. Good checkering to you and hopefully others will chime in with tips and support.
Thomas Garver is offline   Reply With Quote
Unread 05-01-2016, 07:04 AM   #10
Member
BRDHNTR
PGCA Lifetime
Member

Member Info
 
Join Date: Nov 2012
Posts: 2,564
Thanks: 2,658
Thanked 1,444 Times in 671 Posts

Default

Thanks all for the good advice that I shall follow should I decide to pick up this Trojan 16. I carved and made my own decoys for years and I'm familiar with working with wood. I'll take it slow, one step at a time but I know I can do this. Thanks again to all.
allen newell is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:10 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright 1998 - 2019, Parkerguns.org
Copyright 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.