Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums Parker Hammer Guns

Notices

Reply
Thread Tools Display Modes
Early 1/2 Frame 12 Gauge Lifter?
Unread 12-06-2016, 11:09 PM   #1
Member
Jay Oliver
PGCA Lifetime
Member
 
Jay Oliver's Avatar

Member Info
 
Join Date: Jan 2014
Posts: 1,032
Thanks: 1,301
Thanked 3,147 Times in 622 Posts

Default Early 1/2 Frame 12 Gauge Lifter?

Hello Everyone,

I picked up a new lifter today. It’s serial# 3492 a 12 gauge lifter, Dollar Grade 2 I believe with 30” damascus barrels. When I got it home and was checking it out it seemed like a very light weight 12 gauge especially for an early lifter. On a bathroom scale it weighed 7lbs. 10 oz. That doesn’t seem that light now but maybe it was back in 1874?

Also the barrel thickness at the breach is the thinnest I have seen in a Damascus gun. The chambers measured 2 5/8” a 2 ½ RST 12 gauge shell seems very loose(side to side until it seated) in the chamber. I put in 2 Original 12A Parker Brass shells, which fit much better. I thought maybe these barrels were honed/polished to the point where there wasn’t too much metal left? I don't know if you can tell from the pictures?

I measured the frame, 1 1/16” between the firing pins, 1 5/8” across the water table on the frame and 2 5/32” across the bolsters(which look like grade 1 instead of grade 2). Would that make this a 1/2 frame 12 gauge? I thought that might explain the light weight barrels.

If you zoom in on the barrel and forearm picture you can see 12 stamped in the barrel. Also JL under it but upside down(Initials?). There isn’t a barrel weight on the lug, except maybe a “1” or “L” that may be part of the initials.
Overall a very nice gun, bores are nice but not perfect so that may support some polishing. The rest of the gun seems to be in good condition(all the numbers match). I have never seen that type of bead on a Parker.

It is nice to shoulder, when I measured the LOP between the triggers it was 12 ¾” which I usually wouldn’t like, but the gun feels light and nice. Shooting these thin chambers concerns me a bit, this seems like a black powder gun with light loads. Any thoughts or ideas are appreciated?

I have a research letter on the way.

Thank you,
Jay
Attached Images
File Type: jpg 1Lifter74.jpg (293.0 KB, 3 views)
File Type: jpg 2Lifter74.jpg (342.0 KB, 2 views)
File Type: jpg 3Lifter74.jpg (372.8 KB, 7 views)
File Type: jpg 4Lifter74.jpg (465.5 KB, 6 views)
File Type: jpg 5Lifter74.jpg (435.7 KB, 5 views)
Jay Oliver is offline   Reply With Quote
The Following 3 Users Say Thank You to Jay Oliver For Your Post:
Unread 12-06-2016, 11:11 PM   #2
Member
Jay Oliver
PGCA Lifetime
Member
 
Jay Oliver's Avatar

Member Info
 
Join Date: Jan 2014
Posts: 1,032
Thanks: 1,301
Thanked 3,147 Times in 622 Posts

Default

I updated my bolster measurement above, when I looked at my calipers again, I get slightly less than 2 3/16" between the bolsters, its more like 2 5/32"
Attached Images
File Type: jpg 6Lifter74.jpg (523.0 KB, 3 views)
File Type: jpg 7Lifter74.jpg (495.8 KB, 6 views)
File Type: jpg 8Lifter74.jpg (438.1 KB, 1 views)
File Type: jpg 9Lifter74.jpg (453.2 KB, 5 views)
File Type: jpg 10Lifter74.jpg (525.0 KB, 11 views)
Jay Oliver is offline   Reply With Quote
The Following 2 Users Say Thank You to Jay Oliver For Your Post:
Unread 12-06-2016, 11:12 PM   #3
Member
Jay Oliver
PGCA Lifetime
Member
 
Jay Oliver's Avatar

Member Info
 
Join Date: Jan 2014
Posts: 1,032
Thanks: 1,301
Thanked 3,147 Times in 622 Posts

Default

And 2 More...

Thanks,
Jay
Attached Images
File Type: jpg 11Lifter74.jpg (354.4 KB, 8 views)
File Type: jpg 12Lifter74.jpg (292.9 KB, 1 views)
Jay Oliver is offline   Reply With Quote
The Following 3 Users Say Thank You to Jay Oliver For Your Post:
Unread 12-07-2016, 07:52 AM   #4
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 31,557
Thanks: 35,430
Thanked 33,039 Times in 12,321 Posts

Default

Well, the 1/2-frame wasn't developed until Remington owned the Parker Gun Works so it can't be a 1/2-frame. Your gun is however from an era when 'standards' as we know them today had not yet been fully implemented. We see similar variances from the norm in other guns made in that period. A 20 gauge lifter owned by member Tom Latham comes to mind. The spacing between centers of the firing pin holes, as I recall are closer together than on a 0-frame and we know that the 00-frame hadn't been developed yet. I have only ever examined two such 20 gauge guns, the other having been owned by Austin Hogan.
That is certainly the era of anomalies... but, as I stated, the development of 'standards' was in its youth - if not its infancy.
I am not aware of Parker Bros. ever having made the 12 gauge on anything smaller than the 1-frame... but again, it is an early gun.






.
__________________
"I'm a Setter man.
Not because I think they're better than the other breeds,
but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture."

George King, "That's Ruff", 2010 - a timeless classic.
Dean Romig is offline   Reply With Quote
The Following User Says Thank You to Dean Romig For Your Post:
Unread 12-07-2016, 08:16 AM   #5
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 10,546
Thanks: 476
Thanked 17,411 Times in 4,591 Posts

Default

This gun really predates what is considered the typical Parker frame sizing system.

It simply is a super loghtweight 12g gun. Looks to be in super condition!
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
The Following User Says Thank You to Brian Dudley For Your Post:
Visit Brian Dudley's homepage!
Unread 12-07-2016, 08:22 AM   #6
Member
OH Osthaus
PGCA Lifetime
Member
 
Rick Losey's Avatar

Member Info
 
Join Date: Jul 2010
Posts: 7,797
Thanks: 1,641
Thanked 8,138 Times in 3,254 Posts

Default

Quote:
Originally Posted by Jay Oliver View Post
Hello Everyone,

Also the barrel thickness at the breach is the thinnest I have seen in a Damascus gun. The chambers measured 2 5/8” a 2 ½ RST 12 gauge shell seems very loose(side to side until it seated) in the chamber. I put in 2 Original 12A Parker Brass shells, which fit much better. I thought maybe these barrels were honed/polished to the point where there wasn’t too much metal left? I don't know if you can tell from the pictures?

Shooting these thin chambers concerns me a bit, this seems like a black powder gun with light loads. Any thoughts or ideas are appreciated?

a gun of that age was likely chambered for the brass shells

when you say "thin chambers" are you only referring the the wall at the breach? this sounds like a gun to get wall thickness measured on- but if the brass shells fit, that would make sense. It may like BP in brass hulls as a diet.

Over all - great looking early gun
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
Rick Losey is offline   Reply With Quote
The Following User Says Thank You to Rick Losey For Your Post:
Unread 12-07-2016, 09:22 AM   #7
Member
Roundsworth
PGCA Member
 
Mark Landskov's Avatar

Member Info
 
Join Date: Jun 2010
Posts: 1,452
Thanks: 1,513
Thanked 561 Times in 311 Posts

Default

Very nice! It is not chambered for the smaller B shell, which makes shooting it less of a hassle.

__________________
GMC(SW)-USN, Retired
'Earnest Will'
'Desert Shield'
'Desert Storm'
'Southern Watch'
Mark Landskov is online now   Reply With Quote
The Following User Says Thank You to Mark Landskov For Your Post:
Unread 12-07-2016, 11:02 AM   #8
Member
Jay Oliver
PGCA Lifetime
Member
 
Jay Oliver's Avatar

Member Info
 
Join Date: Jan 2014
Posts: 1,032
Thanks: 1,301
Thanked 3,147 Times in 622 Posts

Default

Thanks for the replies. I was referring to the wall thickness at the chambers/breach. In the picture below you can see there is just enough room for 2 12 gauge shells and not much "barrel material" around them.

At some point the pin was welded/converted so it no longer extends when the the gun is open(I think that was a common practice).

I like it more and more as I look it over. It will be interesting to see what the letter says.
Attached Images
File Type: jpg 13Lifter74.jpg (334.6 KB, 1 views)
Jay Oliver is offline   Reply With Quote
The Following 2 Users Say Thank You to Jay Oliver For Your Post:
Unread 12-07-2016, 01:58 PM   #9
Member
charlie cleveland
PGCA Member

Member Info
 
Join Date: Jul 2009
Posts: 12,986
Thanks: 0
Thanked 7,787 Times in 3,967 Posts

Default

i have a early 10 ga that is thin at the breach end of the gun..just cleaned it the other day and donot remember the serial no...but it is the early 4000 range...you have a very interesting gun there at the barrels end looks to be safe to shoot to me...charlie
charlie cleveland is offline   Reply With Quote
The Following User Says Thank You to charlie cleveland For Your Post:
Unread 12-07-2016, 02:58 PM   #10
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 31,557
Thanks: 35,430
Thanked 33,039 Times in 12,321 Posts

Default

This is the breech of Tom Latham's 20 gauge lifter with Stub Twist barrels. These are pretty thin as well.


.
Attached Images
File Type: jpg DSC_0058.jpg (290.5 KB, 3 views)
File Type: jpg DSC_0018.jpg (323.2 KB, 1 views)
File Type: jpg DSC_0021.jpg (289.1 KB, 0 views)
__________________
"I'm a Setter man.
Not because I think they're better than the other breeds,
but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture."

George King, "That's Ruff", 2010 - a timeless classic.
Dean Romig is offline   Reply With Quote
The Following 2 Users Say Thank You to Dean Romig For Your Post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:29 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.