|
01-29-2019, 07:42 AM | #3 | ||||||
|
Remington did during their time of making and also servicing the Parker gun.
__________________
B. Dudley |
||||||
The Following 7 Users Say Thank You to Brian Dudley For Your Post: |
01-29-2019, 10:13 AM | #4 | ||||||
|
Is it usual procedure when rust bluing to drill weep holes?
|
||||||
01-29-2019, 10:46 AM | #5 | ||||||
|
A lot of people do it, but it is not necessary. In my opinion, it leads to more issues than anything.
__________________
B. Dudley |
||||||
The Following User Says Thank You to Brian Dudley For Your Post: |
01-29-2019, 02:08 PM | #6 | ||||||
|
I spoke with Parker a while back at Bachelders about bluing a set of Barrels and he said it is not always necessary to put a weep hole in the barrel but to always mention the fact when discussing the job that if you do not want the weep hole to always make that fact clear ! So I assume it is pretty much standard practice to put the weep hole in a set of refinished barrels ! I decided not to reblue my barrels but the decision was made at that time not to have a weep hole !
|
||||||
The Following 2 Users Say Thank You to Russ Jackson For Your Post: |
01-29-2019, 04:06 PM | #7 | ||||||
|
Drilling a weep hole is almost never necessary but is an easy shortcut to get the air and impurities out. A good barrel man would seldom if ever need to do it on Parker barrels.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
The Following User Says Thank You to Dean Romig For Your Post: |
01-29-2019, 04:15 PM | #8 | ||||||
|
Lets put it this way... Parker did not do it at Meriden in approx. 60 years of making, finishing and refinishing barrel sets. So... why should it be done today?
__________________
B. Dudley |
||||||
The Following 5 Users Say Thank You to Brian Dudley For Your Post: |
01-29-2019, 06:07 PM | #9 | ||||||
|
Thats a great way of putting it. No need for weep holes at all if you are doing a proper rust blue. I have no idea why anyone would drill a weep hole when rust bluing. If I find one on a barrel I am doing, I plug it using glass bedding compound.
|
||||||
The Following User Says Thank You to Tom Flanigan For Your Post: |
01-29-2019, 06:27 PM | #10 | ||||||
|
Just my two cents. I spoke to Mr. Dan Morgan about this, a barrel man whom I respect. And I also spoke to a gunsmith whom I greatly admired his work before he retired. Both said essentially the same thing. Then I spoke to Mr. Dale Edmonds.
Mr. Morgan said if a set of barrels, for example Parker, went into the boil and there was not a single sign of air escaping from around the ribs then you were OK. But if he saw any sign of air coming out from the ribs, the barrels required the ribs to be relaid before they would be blued. Parker probably never allowed a set to pass if they showed any sign of voids in the solder. The second gunsmith told me that he for years did not believe that a weep hole was necessary. But he disassembled a set that had voids in the solder under the ribs and had been rust blued. The damage of the water left in the ribs and between the barrels was severe. Henceforth, he drilled a weep hole to be sure he got all of the water and water displacing oil from the cavity. Now Mr. Edmonds told me he used a heat gun to get the barrels extremely hot so if there were voids, everything would evaporate, and the water displacing oil would also get rid of the moisture. That is why I feel much more at ease when I do a Fox, Ithaca, or even a Parker where a weep hole exists, and I can blow air in to remove the now milky water displacing oil, and then I submerge them again in oil, and allow the barrels to drain. Sometimes it takes days for it to all come out. The question I had about a Parker with no weep hole and a solid soldering job, did they wait until the barrels were finished before drilling and tapping the front sight to avoid an entry point for water. I would think they did. |
||||||
The Following User Says Thank You to Jerry Harlow For Your Post: |
|
|