Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions General Discussions about Other Fine Doubles

Notices

Reply
Thread Tools Display Modes
Unread 08-27-2019, 02:04 PM   #21
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,526
Thanks: 6,119
Thanked 8,786 Times in 4,718 Posts

Default

Dave, you know me better than that. My PH Twist gun letters as 3 1/2". While you are researching the beginning of the Super X 3 1/2" ten gauge ammunition, I will dig out the date of the #6 frame PH manufacture and verify the chamber length. If it says 3 1/2", and if we are skeptical, maybe Chuck Bishop will confirm. I will post the serial number.
Bill Murphy is online now   Reply With Quote
Unread 08-27-2019, 02:30 PM   #22
Member
Researcher
PGCA Lifetime
Member
 
Dave Noreen's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 3,597
Thanks: 1,617
Thanked 7,773 Times in 2,353 Posts

Default

The earliest listing I have for the 3 1/2 inch Magnum 10-gauge Super-X shell is in the April 1, 1932, Western Ammunition for Rifle, Revolver and Shotgun. It is not in July 1, 1931 or February 1932 Western paper. The Ithaca NID Magnum-10 first appears in the second 1932 Ithaca Gun Co. catalog. Remington didn't add a 10-gauge 3 1/2 inch Magnum shell to their offerings until their January 13, 1937, price lists. Peters didn't list a 3 1/2 inch Magnum 10-gauge load until their January 3, 1950, price lists.
Dave Noreen is offline   Reply With Quote
Unread 08-27-2019, 04:18 PM   #23
Member
Phil C
PGCA Member
 
Phillip Carr's Avatar

Member Info
 
Join Date: May 2009
Posts: 3,154
Thanks: 3,455
Thanked 5,918 Times in 1,432 Posts

Default

You could special order a 10 gauge very early on with 3 1/2” chambers as well as special order the brass shells for it. Do we know the earliest 10 gauge documented with 3 1/2” chambers?
Phillip Carr is offline   Reply With Quote
Unread 08-27-2019, 06:37 PM   #24
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,526
Thanks: 6,119
Thanked 8,786 Times in 4,718 Posts

Default

Serial number of my #6 frame PH is 118,498. Chuck sent me a letter indicating the 3 1/2" chamber. I'm sure he would confirm his research. It is a 1903 gun ordered by Iver Johnson, apparently, certainly, before the Western Super X 2 ounce loads. Dave has posted interesting information.
Bill Murphy is online now   Reply With Quote
Unread 08-27-2019, 06:53 PM   #25
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,526
Thanks: 6,119
Thanked 8,786 Times in 4,718 Posts

Default

Parker Brothers posted maximum loads for their smallbore guns in the popular "Small Bore" pamphlet which were lighter than loads specified in orders for guns in the 1912-1918 era, which were 1 ounce loads. I have owned guns, 20 gauge 3" chamber guns, that were specified to shoot 1 ounce loads when PB didn't admit that they approved of such loads. They were #2 frame 20 gauges, but maybe some smaller frame guns were specified for 1 ounce loads, I don't know. Discussion continues.
Bill Murphy is online now   Reply With Quote
Unread 08-27-2019, 06:57 PM   #26
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,526
Thanks: 6,119
Thanked 8,786 Times in 4,718 Posts

Default

Has Dave "Researcher" lettered the #2 frame 20 gauge barrels I sold to him many years ago to find out the construction of that original gun?
Bill Murphy is online now   Reply With Quote
Unread 08-27-2019, 07:10 PM   #27
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,510
Thanks: 2,882
Thanked 10,213 Times in 1,622 Posts

Default

L.C. Smith used three frame sizes for 10ga guns during the Syracuse era according to David Williamson. Very similar to Parker. L.C. smith did not number the frame sizes but measurements across the breech balls have confirmed it. After the move to Fulton all 10's were built on the same frame.
With Parker TL hammer 10's if you wanted a 8.5lbs to 9lbs gun with 30 to 32 " bbls you got a 3 frame, if you wanted a 10lbs gun with 30 to 32" bbls you got a 4 frame, if you wanted a 10lbs plus gun with barrels over 32" you got a 5 or 6 frame gun. Just my observations but there are always exceptions.
Craig Larter is offline   Reply With Quote
The Following User Says Thank You to Craig Larter For Your Post:
Unread 08-27-2019, 07:31 PM   #28
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,526
Thanks: 6,119
Thanked 8,786 Times in 4,718 Posts

Default

Craig sends us some interesting information, but his observation about frame sizes larger than #4 in hammer guns is a bit incorrect. Hammer guns of ten gauge in frame sizes larger than #4 are rare, #5 almost nonexistent except in very early eight gauge. In sixty some years of collecting, I have never seen a #7 frame hemmer ten gauge. I would like to see one. #7 frame hammer eight gauges are the most often seen.
Bill Murphy is online now   Reply With Quote
The Following User Says Thank You to Bill Murphy For Your Post:
Unread 08-27-2019, 08:26 PM   #29
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,510
Thanks: 2,882
Thanked 10,213 Times in 1,622 Posts

Default

Bill: I value your input and knowledge when it comes to large frame Parkers and agree that 4 and 5 frame TL hammer guns in 10ga are rare. 26498 a B TL hammer is the pinnacle of the big tens, displayed by Mr. L at last year's annual meeting people's choice award.
Craig Larter is offline   Reply With Quote
Unread 08-28-2019, 12:21 AM   #30
Member
Milton C Starr
Forum Associate

Member Info
 
Join Date: Jun 2019
Posts: 1,500
Thanks: 475
Thanked 1,000 Times in 462 Posts

Default

Quote:
Originally Posted by Bill Murphy View Post
"Looks like" doesn't cut it. Milton has a very curious mind, brings up some great ideas, but he needs to invest in a Vernier caliper and give up on the "Looks like". Parker made 3 1/2" chambered tens before the advent of the Super X loads. I have a #6 frame PH that letters as a factory 3 1/2" gun and I'm sure they made a few #3 frame 3 1/2" guns before the Remington era also. I'm not sure if my #6 frame ten PH predates the Super X loads. I have seen 10 gauge Damascus barrel English guns that went through nitro proof with modern 3 1/2" shells also.
I had one years ago because I had thought of sending the Zephyr to Briley for chokes and needed to measure the muzzle diameter to determine for thin walls or regular chokes .

I have seen English ammo catalogs that predate the 10 ga 3.5" Super X of the 1930s . They were 1900s or 1890s catalogs that listed the 10 ga from any length up to 3.5" . Actually They may have listed one longer than that .
I dont doubt that a #3 frame Parkers could handle it . The CG Bonehill I owned had 3.5" chambers though I only shot RST 2 7/8s out of it . The guy I sold it to ran alot of 3.5" shells and never had a problem. That was a heavy barreled gun to start with .
Milton C Starr is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:23 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.