Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums General Parker Discussions

Notices

Reply
Thread Tools Display Modes
Split Stock Repair (Pics)
Unread 09-19-2009, 12:56 AM   #1
Member
VH20
Forum Associate

Member Info
 
Join Date: Dec 2008
Posts: 131
Thanks: 5
Thanked 49 Times in 26 Posts

Default Split Stock Repair (Pics)

We've all seen these guns for sale - often in beautiful shape except for a pin, dowel or even a bolt through the stock head, cheek-to-cheek. This was a common way to repair a common problem with Parkers and other fine doubles - a split stock head. It is an effective way to repair the damage, but a horrendous one in terms of aesthetics and value. It is also totally un-necessary. The stock can be repaired internally with all repairs invisible when the gun is reassembled. I learned this technique years ago when I read "Shotgun Technicana" by Trevallion and McIntosh. Many of you have seen this "staple" technique before, but I offer this pictorial as a work-in-progress for those who haven't seen it before. It has worked very well for me in the past, and I consider it necessary medicine on any stock I repair that has any significant cracking. Occasionally I'll refinish a stock with no visible cracks. For these I'll wick very thin Cyanoacrylate (CA) glue into all the inletting areas to stabilize any invisible or incipient cracks, and to seal the inletting from gun oil. Then I'll just glass bed the action to the stock and forego the staple, the thinking being that if the stock hasn't cracked yet in the past 100 yrs., and the CA glue and glass bedding will make it even that much more resistant to cracking, it should be fine. But if there are any cracks that are significant enough for movement, they get the staple.

The first step (not shown) is to repair the wood itself, and return it to it's original fit and stabilize the cracks with the appropriate adhesive. When cracks can be closed completely (no wood missing) through simple clamping and the fit is perfect, I use CA glue. The very thin formula will wick into cracks so tiny that they can be invisible. There is a medium viscosity formula that works better for larger cracks where small gaps may be present. Finally, when big chunks are broken out that must be replaced, Acraglass (an epoxy) is the best choice. Of course none of these work well if the wood is oil-soaked - you must get that out of the wood first. I've had stocks that separated into as many as five chunks of broken inletted wood when the receiver was removed. If they are all there, they can be carefully fit back together like a puzzle with the Acraglass, then the CA used to wick into the hairline cracks afterwards. This particular project is an 0-frame stock off of the VH 20 I grew up with (my first shotgun, given to me by my great uncle when I was 8). Before these pics were taken, all the chunks of broken inletting and cracks were glued as described above, and the fit to the receiver has been checked and found to be good (in fact I did that last year, and shot a few rounds of skeet, wobble trap, and a couple quail hunts while I had it reassembled). Satisfied with the fit and repair, I have disassembled it again to make the repairs permanent (staple, glass bed, then re-finish, re-checker, etc.) and get the gun finished for this year's season.

In the first pic, you can see the staple has been made from 1/16" stainless rod (actually, this is a cut-off from a surgical steel orthopedic Steinman pin, the remainder of which I installed in some dog's fractured leg somewhere along the way). On the face of the stock head, you can see the holes drilled for the "legs" of the staple, and a channel cut across the face of the stock to allow the crossbar of the staple to sink down below flush. Placement of the legs should be into the meatiest portion of the stock cheeks, and care must be taken to drill vertically to make sure that both leg-holes are parallel (and to make sure you don't drill out the side of the cheek). Hole-to-hole distance must match the dimensions of the staple legs precisely. Once the holes are drilled, a straight edge is used to scribe the borders of the cross channel across the face, then the channel is routed using a small burr in a rotary tool. The depth of the channel must be deep enough to allow the crossbar of the staple to fit below flush with the face of the stock (in order to avoid interference with the receiver fit). Also, where the channel meets each leg-hole, it must be radiused down into the hole to allow for clearance of the inside radius of the bend on each leg of the staple:
[IMG][/IMG]

Last edited by Jim Williams; 09-19-2009 at 01:45 AM..
Jim Williams is offline   Reply With Quote
Unread 09-19-2009, 01:01 AM   #2
Member
VH20
Forum Associate

Member Info
 
Join Date: Dec 2008
Posts: 131
Thanks: 5
Thanked 49 Times in 26 Posts

Default

Once the drilling and routing is done, the staple is carefully fit into place. The holes are not over-bored, but rather drilled to the actual diameter of the pin for a very tight fit. However, repeated working in and out of the staple as it is worked to depth will allow the holes to be worried enough that the staple can be set most of the way with firm hand pressure:[IMG][/IMG]
Jim Williams is offline   Reply With Quote
Unread 09-19-2009, 01:04 AM   #3
Member
VH20
Forum Associate

Member Info
 
Join Date: Dec 2008
Posts: 131
Thanks: 5
Thanked 49 Times in 26 Posts

Default

Almost home. It starts to get real tight around here, and you can't go much deeper without providing a means for retrieval:[IMG][/IMG]
Jim Williams is offline   Reply With Quote
Unread 09-19-2009, 01:08 AM   #4
Member
VH20
Forum Associate

Member Info
 
Join Date: Dec 2008
Posts: 131
Thanks: 5
Thanked 49 Times in 26 Posts

Default

Fully home. If fit properly, it must be driven with a hammer the last 1/4 inch or so, using the flat blade of a small slotted screw driver as a punch. You must provide yourself a means for retrieval before doing this (see the small green wires). Otherwise you will never get it back out. If you were to commit to driving it all the way without means for retrieval, then find out it wouldn't quite go below flush for some reason, you'd be in a mess. But the wires can be used to provide traction and it can be rocked out. By the way, the shiny appearance of the inletting is not oil in the wood, but rather the hardened surface that results from being soaked in CA glue after thorough degreasing:
[IMG][/IMG]

Last edited by Jim Williams; 09-19-2009 at 01:56 AM..
Jim Williams is offline   Reply With Quote
Unread 09-19-2009, 01:24 AM   #5
Member
VH20
Forum Associate

Member Info
 
Join Date: Dec 2008
Posts: 131
Thanks: 5
Thanked 49 Times in 26 Posts

Default

Finally, using a straight-edge to make sure that the crossbar of the staple is well-below flush with the face of the stockhead:[IMG][/IMG]

This is the first 0-frame I've performed this procedure on. It is more difficult, the placement a little less optimal (more towards the bottom, rather than the center of the stock face) and the diameter of the pin is necessarily a little smaller than on the standard 2-frame 12 ga. repair. In fact, I have a 00-frame stock on my bench right now that actually would give me a little more room and a little better placement and maybe a 5/64 in. pin could be used instead of the 1/16 in. used here. Nevertheless, when this pin is installed in this 0-frame stock, it will be locked-in so tightly (first by an initial proper, tight fit, and second by filling in any remaining voids with Acraglass) that it will take incredible force to ever separate the left and right sides again. I am confident this repair will not be necessary again, unless it meets some disastrous fate.

That's about as far as I got tonight. After this pic was taken, the wires were used to remove the staple again. The receiver will now be coated with release-agent in all contact areas, in preparation for glass bedding to the stock. The next step will be to mix the Acraglass and work a little down into the holes and channel for the staple. Then the staple will get a light coating of Acraglass and driven home for the final time. Then I'll apply more Acraglass to the areas of the stock face that contact the receiver, making sure to apply enough to finish filling up the channel for the crossbar. Finally, the receiver will be quickly assembled to the stock (to full tightness) and the assembly will be allowed to cure for 24 hrs. More pics when I get a chance to get back on it.

Jim

Last edited by Jim Williams; 09-19-2009 at 01:50 AM..
Jim Williams is offline   Reply With Quote
The Following 4 Users Say Thank You to Jim Williams For Your Post:
Unread 09-19-2009, 12:30 PM   #6
Member
Gunner
Forum Associate

Member Info
 
Join Date: Nov 2008
Posts: 231
Thanks: 1,456
Thanked 160 Times in 69 Posts

Default

Great Pictoral with straightforward directions Jim. Thanks for sharing.
I have a Trojan with glued twine around the wrist but no nasty pin that I need to do this same thing for.
Erick
Erick Dorr is offline   Reply With Quote
Unread 09-19-2009, 01:38 PM   #7
Member
Rod N. Gunn
Forum Associate
 
Dave Fuller's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 429
Thanks: 117
Thanked 169 Times in 62 Posts

Default

I wish I had taken a picture of the stock head of the Repro I recently had apart. It had a wooden bridge in the same location as Jim's pin. I assume that it came from the factory that way but I don't know. Either way it is a very good feature given that these stocks seem to split in this same area fairly often. Like a cross bolt in a rifle, its a good preventative devise. By the way, nice job and good tutorial Jim - thanks.
Dave Fuller is offline   Reply With Quote
Unread 09-19-2009, 03:01 PM   #8
Member
Drew Hause
Forum Associate
 
Drew Hause's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,084
Thanks: 323
Thanked 3,761 Times in 1,245 Posts

Default

Wonderful tutorial Jim! Pics of Trevallion's staple technique are here http://www.picturetrail.com/sfx/album/view/15127852 (scroll down about 2/3s)



This is nice though

Drew Hause is offline   Reply With Quote
Visit Drew Hause's homepage!
Split Stock Repair (now glass-bedded)
Unread 09-20-2009, 09:30 PM   #9
Member
VH20
Forum Associate

Member Info
 
Join Date: Dec 2008
Posts: 131
Thanks: 5
Thanked 49 Times in 26 Posts

Default Split Stock Repair (now glass-bedded)

Continuing on, the staple was ready and the receiver and trigger plate had been coated in the appropriate areas with release agent. A small amount of Acraglass epoxy was mixed along with some dye and fiberglass fiber floc for strength. A small pin was used to work some epoxy down into the holes drilled for the staple, then into the channel for the crossbar of the staple, and then finally a little was applied to the staple itself. Then the staple was inserted and driven fully home. A thin coating of the epoxy was then applied to the face of the stock, avoiding any in the circular recesses that allow for tumbler clearance when the gun is cocked. Also enough epoxy was applied to fill-in the channel cut for the staple crossbar. Then the receiver is quickly assembled to the stock without any fumbling or allowing it to slide around and smear the epoxy out of place. It isn't necessary, but I put everything in the stock that will be in there at the end - the safety mechanism, auto-safety rod (if desired), and top wrist-pin ferrule. It is a good idea to practice the assembly of the receiver to the gun a couple times before applying the epoxy so that you can assemble it smoothly, quickly, and without excess movement once you are ready to do it for real. The idea is to press the receiver into place, hold it tightly to the stock while you flip it over and tap the triggerplate in place, and get some screws in it to hold it firmly in place. Then you tighten all the screws down to their working tightness. A common trick of stockers is to not tighten the last 1/16 of a turn (stopping before the slots are fully qualified) until final assembly. It saves wear on the threads and assures that they will be good and tight when they are fully-qualified (slots oriented precisely as they should be). That technique works fine here. When everything is tightened down, the epoxy is allowed to cure at least 12 hrs. I parted this receiver from the stock at around the 15 hour mark. It is always a moderately tense moment, as you hope you didn't overlook something and allow the epoxy to get in somewhere that will "lock" the receiver to the stock. When ready, the screws are removed, the trigger plate is tapped out the bottom of the receiver with a soft aluminum or brass drift, and then the receiver is parted from the stock. It will usually be stuck fairly tightly, but light taps with a plastic hammer will gently jar it loose with some patience. Hold the gun around the wrist using your thumb to press down on the top tang to keep the receiver from falling when it breaks loose, then tap gently in a downward direction on the water table. Eventually you will either feel it start to move, or sometimes they just break free all at once - that's why it's good to have your thumb on the tang to keep it from falling. Once broken loose, you can carefully remove the receiver. Here's what it looks like at that point, before the "flashing" (excess epoxy that has squeezed out) is cleaned up:[IMG][/IMG]
Jim Williams is offline   Reply With Quote
Unread 09-20-2009, 09:35 PM   #10
Member
VH20
Forum Associate

Member Info
 
Join Date: Dec 2008
Posts: 131
Thanks: 5
Thanked 49 Times in 26 Posts

Default

Another view showing the footprint of the receiver on the stock, outlined by the excess epoxy:[IMG][/IMG]
Jim Williams is offline   Reply With Quote
The Following 3 Users Say Thank You to Jim Williams For Your Post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:13 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.