Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums Parker Restoration

Notices

Reply
Thread Tools Display Modes
Advice on Restoring 1919 VHE 12ga
Unread 09-28-2016, 01:18 PM   #1
Member
Allan McKinney
Forum Associate

Member Info
 
Join Date: Jul 2012
Posts: 9
Thanks: 0
Thanked 2 Times in 2 Posts

Default Advice on Restoring 1919 VHE 12ga

My VHE is on a 1-1/2 frame, 12ga, 28" F/F. It is still so tight that I have to open the action a little for the fore end to latch. 10% CC, 90% bluing going a little thin. The wood is original and solid but with a couple of gouges that won't sand out. A few chips in the original DHBP. What would a complete restoration using existing wood, but leaving the gouges cost? What are the before and after values?
Allan McKinney is offline   Reply With Quote
Unread 09-28-2016, 01:40 PM   #2
Member
OH Osthaus
PGCA Lifetime
Member
 
Rick Losey's Avatar

Member Info
 
Join Date: Jul 2010
Posts: 7,797
Thanks: 1,641
Thanked 8,138 Times in 3,254 Posts

Default

personally- not sure why you would- sounds like a good honest gun

but if you want to go ahead with it- your best action might be to send good high-res pictures to someone like Brian Dudley and get a ball park estimate - of course anyone would need to actually see the gun to be truly accurate in an estimate
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
Rick Losey is offline   Reply With Quote
The Following User Says Thank You to Rick Losey For Your Post:
Unread 09-28-2016, 05:19 PM   #3
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,510
Thanks: 2,882
Thanked 10,213 Times in 1,622 Posts

Default

Before restoration $1200. After restoration $1200.
Restoring a common field grade gun is losing proposition in my opinion. If you are not happy with the vhe , sell it and look for a high condition example you will be way ahead in the long run.
Craig Larter is online now   Reply With Quote
The Following 8 Users Say Thank You to Craig Larter For Your Post:
Unread 09-28-2016, 11:25 PM   #4
Member
Steve Havener
Forum Associate

Member Info
 
Join Date: Feb 2011
Posts: 168
Thanks: 1
Thanked 68 Times in 56 Posts

Default

Have you tried steaming out the gouges? If not soak a clean cloth in water, lay it on the dents/gouges and apply heat, the wife's steam iron will work but don't get caught ( I speak from experience) two or three applications should start raising the dents. You can usually fill any remaining scratches by sanding in a good oil finish.
Steve Havener is offline   Reply With Quote
The Following User Says Thank You to Steve Havener For Your Post:
Unread 09-28-2016, 11:51 PM   #5
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 10,547
Thanks: 476
Thanked 17,411 Times in 4,591 Posts

Default

If the wood grain is broken, steaming will not do much.
It will have an effect on shallow dents.
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
Visit Brian Dudley's homepage!
Unread 09-29-2016, 09:37 AM   #6
Member
Allan McKinney
Forum Associate

Member Info
 
Join Date: Jul 2012
Posts: 9
Thanks: 0
Thanked 2 Times in 2 Posts

Default

Thanks. That's what I thought. It's my rainy day gun in addition to being a backup, so it wouldn't make sense to try to make it into a silk purse. By the way, RST spreader loads in the right barrel work well for close shots.
Allan McKinney is offline   Reply With Quote
Unread 09-29-2016, 09:45 AM   #7
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 10,547
Thanks: 476
Thanked 17,411 Times in 4,591 Posts

Default

Barrel blue is one thing if it needs it. But i would not recommend case color work on the gun if the wood cannot be made to look like new. Especially on a gun that is going to be used a lot.
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
Visit Brian Dudley's homepage!
Unread 10-09-2016, 03:03 PM   #8
Member
Ruff Hunter
PGCA Member

Member Info
 
Join Date: Jun 2010
Posts: 349
Thanks: 86
Thanked 541 Times in 108 Posts

Default

Allan,
It is hard to determine whether your VHE warrants a restoration. Photos are always helpful in that regard. Last year I purchased a VHE at auction on GB for around $900. The finishes were worn and the forend wood was cracked and chipped, requiring some glass work. I restored the case colors, stocks, and bluing. Had I done that work for a client, the cost would have been around $800. I am keeping that VHE as my new pheasant gun, but if I were to sell it, I believe it would bring close to $2,000 at auction. So while there might not be a lot of quick profit in having a restoration done, in most cases the increase in the gun's value will cover the costs.
Others will say that they would rather have a gun with no finishes left than one that has been restored, and that's fine too. To each his own. The bottom line is that its your gun and you shouldn't let anyone tell you what to do with it. Do whatever brings you the most pleasure when you handle and shoot it.

The current home page cover photo is a PH grade that I restored this spring.
WWW.CLASSICCASECOLORSLLC.COM
Justin Julian is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:04 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.