|
04-28-2013, 04:01 PM | #3 | ||||||
|
thanks OH, I mainly need a higher comb and longer LOP.
here is a couple pics to better illustrate what I am dealing with. on this one most of what looks like a gap is proud wood, but there is a gap there none the less with this picture what appears to be a gap is mostly proud wood and shadow, but there is still a gap. Im sure Im splitting hairs and a duplicator would probably leave this much behind for me to work with but I have never used one before so I want as solid a foundation as possible, especially if I give him a piece of wood worth anything. I don't mind adding bondo and tweaking the stock to fit the dimensions I want, after the old stock gets duplicated its going to be my practice board for checkering. |
||||||
04-28-2013, 06:23 PM | #4 | ||||||
|
Mike, From the pictures I can't tell if that is a factory stock or not. Removing the trigger guard bow and looking in the channel for it there should be stamping with the serial number. Also when Parker guns left the factory the wood was always a bit proud of the frame.
__________________
"Much care is bestowed to make it what the Sportsman needs-a good gun"-Charles Parker |
||||||
04-29-2013, 10:55 AM | #5 | ||||||
|
What dimensions do you require? When I run a stock on my duplication machine, I try to use the original stock, but often I cannot since the stock is being replaced due to manly damage and the original is not suitable for a pattern. Or, it is not worth taking the time to repair when I can just use a pattern that I have on hand.
Obviously if the dimensions you require are abnormal, your original can be modified and use as a pattern. Another issue with just trusting an off the shelf duplication is that there is a lot of variation in these guns, especially in the rear tangs and the amount of bend they have. So, unless your original stock is duplicated, or your action is checked against the pattern to be used, there is a chance for issues.
__________________
B. Dudley |
||||||
The Following User Says Thank You to Brian Dudley For Your Post: |
04-29-2013, 01:35 PM | #6 | ||||||
|
This is a VH with a black walnut stock... and I'm willing to bet the head is split. Hence the gap and wood misalignment. A proper fix should correct that. If you need more comb height, why not try one of the add-on comb pads? Same for the LOP with those type pads. They are not beautiful, but they are functional.
Otherwise, you can spend hundreds on a restock. |
||||||
04-29-2013, 02:34 PM | #7 | ||||||
|
Alder,
Do you have an original buttplate on your gun?
__________________
B. Dudley |
||||||
04-29-2013, 04:37 PM | #8 | ||||||||||
|
Quote:
the replacement stock is proud on one side but not the other... now that I have the trigger guard off, its looks more like the frame is torqued to one side rather than leaning, if that makes sense? Brian: Quote:
Brian: Quote:
John Campbell: Quote:
I really like learning the many different aspects of gunsmithing so I was planning on restocking this gun myself, not that I could afford the work of a real gun smith anyway. plus the stock isn't orginal so I figure I might as well swap it out for something fancier, otherwise I would do like you suggested and just leave it alone or get a strap on pad. |
||||||||||
04-29-2013, 05:26 PM | #9 | ||||||
|
By modern dimentions, do you mean like 1.5" and 2.5" drops? In this range with about a 14 - 14.5" pull is what I would consider modern.
If you want a ssbp put on it, then you are looking at making a new stock or finding an original DH stock to fit up to your gun.
__________________
B. Dudley |
||||||
04-29-2013, 07:29 PM | #10 | |||||||
|
Quote:
making a new stock or having the current one slightly modified and duplicated is definitely the route I would prefer to go over trying to find a different parker stock to try and make fit properly. besides I figure if I muck up the SSBP I can always trim it and slap on a silvers pad and still be able to have my desired LOP. |
|||||||
|
|