Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions Shotgun Shell Reloading

Notices

Reply
Thread Tools Display Modes
1 ounce 410 load
Unread 04-03-2011, 08:21 PM   #1
Member
charlie cleveland
PGCA Member

Member Info
 
Join Date: Jul 2009
Posts: 12,986
Thanks: 0
Thanked 7,787 Times in 3,967 Posts

Default 1 ounce 410 load

some where in my looking at things i think i saw a 410 load of 1 ounce...i may have just got this on my mind and i may have not seen one but im pretty sure i did...has anyone else out there seen a 1 ounce load in the 410..sure would be nice if someone has... charlie
charlie cleveland is offline   Reply With Quote
Unread 04-03-2011, 09:28 PM   #2
Member
C.O.B.
Forum Associate
 
Rich Anderson's Avatar

Member Info
 
Join Date: May 2009
Posts: 6,072
Thanks: 2,217
Thanked 6,320 Times in 2,082 Posts

Default

I looked through some older 3" 410 shells and none were 1oz loads. I found no loading data for a 1oz 410 either.
Rich Anderson is offline   Reply With Quote
Unread 04-03-2011, 10:36 PM   #3
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 31,562
Thanks: 35,442
Thanked 33,041 Times in 12,322 Posts

Default

I'll bet such a load would print horrible patterns.
Dean Romig is offline   Reply With Quote
Unread 04-03-2011, 11:33 PM   #4
Member
Blind Dog
Forum Associate
 
Fred Preston's Avatar

Member Info
 
Join Date: May 2009
Posts: 636
Thanks: 424
Thanked 398 Times in 193 Posts

Default

Charlie, Like you, I sometimes like to mess around with ideas like a 1oz .410 load. I found some 9.3x74R cases and fire formed them in the .410 chamber. The rim and base fit right and the oal is 2&15/16". Since the S&W mod. 29 chamber is capable of handling more than 40K psi, I figured that the chamber wall thickness of the (non Parker) .410 is more than adquate to take just about anything I could load in this case. Anyway, the most shot I could get in this brass case (with thin walls, but sort of high base) was 7/8 oz using only two over powder cards (no fiber). As Dean mentioned, the pattern was pretty broad and inconsistent through the full chokes; maybe a grouse load as I have trouble conecting with that elusive poultry anyway
Fred Preston is offline   Reply With Quote
Unread 04-04-2011, 05:37 PM   #5
Member
Roundsworth
PGCA Member
 
Mark Landskov's Avatar

Member Info
 
Join Date: Jun 2010
Posts: 1,452
Thanks: 1,513
Thanked 561 Times in 311 Posts

Default

Charlie, when Winchester introduced the Model 42 in the early '30s, they or Western, announced the new 3" shell with a 3/4 ounce payload. Only in the past few years, has the 3/4 ounce load been available, again, from Winchester-Western. Ideally, the payload of shot should be 'square'. That is to say, that the height of the payload should be as close to, or equivilent to the diameter of the payload. The 16 bore has been touted as probably the most ideal shotgun because of these dimensions. Even the 3/4 ounce .410 is disproportionate in regards to the height of the payload compared to the diameter. Increasing that load would not help performance. That may be why a 1 ounce load has never been marketed.
__________________
GMC(SW)-USN, Retired
'Earnest Will'
'Desert Shield'
'Desert Storm'
'Southern Watch'
Mark Landskov is offline   Reply With Quote
Unread 04-04-2011, 07:57 PM   #6
Member
Paul Harm
Forum Associate

Member Info
 
Join Date: Nov 2008
Posts: 1,774
Thanks: 44
Thanked 756 Times in 417 Posts

Default

The guys at my club shoot 3/4, 7/8, or 1oz in the 12ga. I myself shoot between the 3/4 and 7/8 - 360grs. Now we're talking about short shot height - it seems to be like tightening up the choke. Still bangs clays and is lighter on the shoulder and wallet. Paul
Paul Harm is offline   Reply With Quote
Visit Paul Harm's homepage!
Unread 04-04-2011, 11:06 PM   #7
Member
charlie cleveland
PGCA Member

Member Info
 
Join Date: Jul 2009
Posts: 12,986
Thanks: 0
Thanked 7,787 Times in 3,967 Posts

Default

boy i was hoping some one else had seen the 1 ounce load...im still pretty sure ive seen one but then again..... i too have fooled around with the 410 loads..you can get the 1 ounce of shot in a 3inch shell but you cannot crimp it..you can lightly roll crimp it and it will work... the wads have to be very thin against the powder to work to be able to get 1 ounce in the in the 3 in hull...i shot these loads through a 12 ga single barrel using the savage 410 tenner insert..the old sigle barrel was choked clyinder bore.. at 30 yards would have been a dead quail on paper.. always thought a tighter choke might make the pattern tighter but it might make it worse..what do yall think.... charlie
charlie cleveland is offline   Reply With Quote
Unread 04-06-2011, 10:42 AM   #8
Member
Chuck Heald
Forum Associate

Member Info
 
Join Date: Feb 2010
Posts: 422
Thanks: 24
Thanked 172 Times in 77 Posts

Default

Charlie,
I'm an avid fourtenner, but I think 1 ounce thru a .410 with a 3" shell length is unreasonable and as others have speculated, I too think it will not perform well.

Hmmm, maybe a 3 1/2" wildcat???

I use the 3" 3/4 oz on wild pheasant and chukar with very good success. Last weekend, I shot a farm raised pheasant up the exhaust pipe from about 30 yrds with a 11/16 oz #4 shot Federal load. One shot and it was dead when it hit the ground.
Chuck Heald is offline   Reply With Quote
Unread 04-06-2011, 11:59 AM   #9
Member
charlie cleveland
PGCA Member

Member Info
 
Join Date: Jul 2009
Posts: 12,986
Thanks: 0
Thanked 7,787 Times in 3,967 Posts

Default

is not the 12 ga 3 1/2 inch shell with 2 1/4 ounce load out of squire with ite lenght and depth but yet it works well...why should the 410 3 inch with 1 ounce not work well... i have shot and patterned only a few rounds of this load...but i will try a few more when i get a chance.... charlie
charlie cleveland is offline   Reply With Quote
Unread 04-06-2011, 12:58 PM   #10
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,524
Thanks: 6,119
Thanked 8,785 Times in 4,718 Posts

Default

Bore the steel Savage Fourtenner out to 3 1/2" or 4" chamber and load an extra length brass .410 with an ounce of shot and try it out. One thing we know is that you're not going to blow up a 12 or 20 gauge barrel with a Fourtenner in it. There is way too much steel in there to be a problem. Don't increase the powder charge, just the shot charge. 14 or 15 grains of 296 should be about right. Pressure will probably be about 13,500. Velocity will be a little slow. Use a regular plastic wad with the petals cut off. To lower the pressure, use a powder just a tad slower than the 296, but it won't be a shotgun powder. Shoot it in a gun with choke this time. You may be surprised at the performance. Charlie, you're intent on doing this, so get going.
Bill Murphy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:57 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.