|
 |
 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
 |
01-23-2021, 08:26 AM
|
#3 | ||||||
|
3 in One on wear areas and ballistol on everything else including items other than firearms.
|
||||||
|
|
||||||
 |
 |
 |
| The Following User Says Thank You to George Lang For Your Post: |
|
|
|
01-23-2021, 08:36 AM
|
#4 | ||||||
|
Generally I wipe things down lightly with Clenzoil. For moving parts a tiny drop of any gun oil or a thin film of Lubriplate on larger moving surfaces (if George Digweed uses it it's good enough for me...) I don't get the "oil/solvent/cleaner" all in one thing. I know folks use Breakfree or Clenzoil as a bore cleaner and lubricant all in one but always believe separate products do a better job. I use Shooters Choice bore solvent followed by Shooters Choice Shotgun and Choke Tube Cleaner (to me nothing melts plastic wad material like this) if it's bad in there. For the bore a film of CLP. There are a lot of these things out there and to me always not much difference in products but then again I don't live near salt water or corrosive environments
https://www.youtube.com/watch?v=uOB5eCReAQY
__________________
Nothing ruins your Friday like finding out it's only Tuesday |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Andrew Sacco For Your Post: |
|
|
|
01-23-2021, 08:55 AM
|
#5 | |||||||
|
Quote:
Tests were done with all types of oils and WD-40 WAS THE WINNER! Harry |
|||||||
|
|
|
|||||||
|
|
|
| The Following 2 Users Say Thank You to Harry Gietler For Your Post: |
|
|
|
01-23-2021, 09:02 AM
|
#6 | |||||||
|
Quote:
Tests were done with all types of oils and WD-40 WAS THE WINNER! Hoppes gun oil on joints. Harry |
|||||||
|
|
|
|||||||
|
|
|
| The Following User Says Thank You to Harry Gietler For Your Post: |
|
|
|
01-23-2021, 09:35 AM
|
#7 | ||||||
|
FYI, the broader topic of cleaning and care is dealt with on the FAQ page off the main web page, in FAQ #9; #10; #20 under the Parker Maintenance and Repair section. (thanks to Bindlestiff for this reference.)
__________________
"First off I scoured the Internet and this seems to be the place to be!” — Chad Whittenburg, 5-12-19 |
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to Russell E. Cleary For Your Post: |
|
|
|
01-23-2021, 09:41 AM
|
#8 | ||||||
|
G 96 for rust prevention, after cleaning. doesn't harm wood,
|
||||||
|
|
|
||||||
|
|
|
| The Following 3 Users Say Thank You to ED J, MORGAN For Your Post: |
|
|
|
01-23-2021, 09:43 AM
|
#9 | |||||||
|
Quote:
|
|||||||
|
|
|
|||||||
|
|
|
| The Following User Says Thank You to Steve Campbell For Your Post: |
|
|
|
01-23-2021, 10:01 AM
|
#10 | ||||||
|
Good ol' "Bindlestiff" - I sure do miss him on this forum.
.
__________________
"I'm a Setter man. Not because I think they're better than the other breeds, but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture." George King, "That's Ruff", 2010 - a timeless classic. |
||||||
|
|
|
||||||
|
|
|
| The Following 2 Users Say Thank You to Dean Romig For Your Post: |
 |
|
|
Linear Mode
