Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Parker Forums Parker Reproductions

Notices

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Many hours later...
Unread 01-22-2019, 01:30 PM   #1
Member
B. Dudley
PGCA Lifetime
Member
 
Brian Dudley's Avatar

Member Info
 
Join Date: Aug 2011
Posts: 10,546
Thanks: 476
Thanked 17,411 Times in 4,591 Posts

Default Many hours later...

I have been working in my spare time in the evenings and weekends for the last few months, an hour hear and an hour there, to clean up and "Meriden-ize" a Parker Repro A-1 Special that was "In-the-white".

The Repros were modeled after very late Remington manufactured guns, when frame sculpting got a little less refined than earlier guns. When I really got to studying the lines of the gun, I found a lot of areas to be relatively crudely finished, ie: contour lines that were not true and straight. I set off to re-shaping the frame and refining the lines. My goal was for the gun to look as true to early Meriden manufacture as possible.

The shoe filing on the bottom of the frame was deepened and lengthen back towards the trigger plate. The belly of the frame and forend iron were brought up a LOT and then the radius in front of the trigger plate was defined. The sides of the frame around the hinge pin were also thinned up along with the forend iron.

I rounded up and better defined the front of the side panels on the frame. Also, the bottom of the side panels was brought up by nearly 1/8" and a very hard line was used to break the bottom of this panel. The radius under the panel was taken in for a better transition into the trigger plate.

The trigger plate was converted to accept double triggers vs. the SST that was in it. This process is explained in another thread.

The breech end of the barrels were rounded over at the corners a good deal. This was all taken down to make a seamless transition into the breech balls. The triple beaded fences were also cleaned up and taken in tighter on top and bottom sides.

A major area of refinement was the top lever and the top of the frame where the sighting plane starts. The Later Parkers, and the Repros had a very thick top lever which allowed the concave sighting plane to come very far back onto the top lever. I took the top lever WAY down in thickness and re-contoured it to move the start of the sight plane up closer to the rib extension.
The thumb pad on the top lever was also reduced in size by nearly 50% for a much more streamlined look. Both of these made a world of difference in the side profile of the gun.

The top of the frame behind the bolsters was re-contoured and the line between them and the side panels was refined and sharpened up.

The top tang bevel was sharpened up at the front, and then extended down the full length of the tang as it was simply left flat previously.

Finally a new safety button was made from scratch in the original A-1 style which truly sets the gun apart from the pack.


All of this work also removed about 1 oz. of metal from the frame. Another benefit.

All of the definition of the frame lines makes things a lot easier when it comes time for engraving, so that the border work can be good and true.

Enjoy some photos below of before and after the work above was performed. This work in all was about 20 hours of time.


Left Side Before

Before 3.jpg

Before 5.jpeg


Left Side After

IMG_2988.jpeg




Bottom Before

Before 11.jpeg

Before 9.jpeg


Bottom After

IMG_2989.jpeg

IMG_2990.jpeg




Top Before

Before 6.jpg


Top After

IMG_2985.jpeg

IMG_2986.jpeg




Safety Button Before

Before 7.jpg


Safety Button After

IMG_2995.jpeg




Bottom Quarter Before

Before 8.jpg


Bottom Quarter After

IMG_2993.jpeg




A few more afters

IMG_2991.jpeg

IMG_2994.jpeg
__________________
B. Dudley
Brian Dudley is offline   Reply With Quote
The Following 78 Users Say Thank You to Brian Dudley For Your Post:
allen newell, Bill Jolliff, Bill Murphy, Bill Zachow, Bob Decker, Bob Jurewicz, Bob Kimble, Brett Farley, Brett Hoop, Brian Arthur, Buddy Marson, Charles Shelton, chris dawe, Chris Robenalt, Chris Taylor, Craig Larter, Daryl Corona, Dave Noreen, David Noble, Dean Freeman, Dean Romig, Dylan Rhodes, edgarspencer, Eric Eis, Eric Estes, Eric Johanen, Frank Cronin, Garry L Gordon, Garth Gustafson, Gary Bodrato, Gary Carmichael Sr, Gary Laudermilch, George Davis, GunnerGrilli, Harry Collins, Henry McRoberts, Henry Verri, Jacob Duke, Jay Gardner, Jeff Christie, Jim Thynne, John Brazelton, John Dallas, John Davis, keavin nelson, Ken Snyder, Larry Stauch, Linn Matthews, Lloyd Bernstein, Louis Caissie, Mark Britton, Mark Garrett, Mark Ray, Michael Earls, Michael Lansing, Michael Murphy, Mike Franzen, Mike McKinney, Paul Ehlers, Pete Kappes, Pete Thompson, Randy G Roberts, Richard Flanders, Robert Brooks, Ron Gebhart, Russ Jackson, Sara LeFever, scott kittredge, Shawn Wayment, Stan Hillis, Steve Huffman, Steven Wilson, Timothy Salgado, todd allen, Tom Hawkins, Tom Pellegrini, tom roberts, William Woods
Visit Brian Dudley's homepage!
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:26 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.