Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions Shotgun Shell Reloading

Notices

Reply
Thread Tools Display Modes
roomy hull
Unread 10-25-2018, 04:36 PM   #1
Member
OH Osthaus
PGCA Lifetime
Member
 
Rick Losey's Avatar

Member Info
 
Join Date: Jul 2010
Posts: 7,798
Thanks: 1,641
Thanked 8,138 Times in 3,254 Posts

Default roomy hull

i got the 2 3/4 Cheditte hull to use some reclaimed TM shot- planning to use Craig's recipe he had tested.

And since i have a lot of bismuth to use up and thought i would load some of that as well

i found this load on the Hodgon site - for a 2 3/4 Cheditte hull



when i loaded it ( powder and shot were weighed to make sure it was right)
i ended up with a tremendous amount of room left in the case

so i went to the 1 3/8 load from the same site



and still had too much room left to crimp over

this is the left over room with a shot load of 1 3/8 oz (not to mention the bit of powder that got past the wad)



how the heck did they test this load -

i tried cheerios - they crushed - so now to find a filler that will hold up
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
Rick Losey is offline   Reply With Quote
Unread 10-25-2018, 04:52 PM   #2
Member
Kensal Rise
PGCA Member

Member Info
 
Join Date: Sep 2011
Posts: 1,768
Thanks: 580
Thanked 2,575 Times in 925 Posts

Default

Why not try a different plastic wad? Like the Claybuster 12 for 1 oz. or 7/8 oz. loads. It won't change pressure that much and ought to fill out the hull's capacity. Just a thought.
John Campbell is offline   Reply With Quote
Unread 10-25-2018, 04:56 PM   #3
Member
OH Osthaus
PGCA Lifetime
Member
 
Rick Losey's Avatar

Member Info
 
Join Date: Jul 2010
Posts: 7,798
Thanks: 1,641
Thanked 8,138 Times in 3,254 Posts

Default

i'll try a few things -

but the point is - unless all three scales are wrong- as well as the calibration weights - who would list this as a tested load - the 1 1/4 ounce load would easily fit into a 2 1/2 hull and might still need a little filler in that
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
Rick Losey is offline   Reply With Quote
Unread 10-25-2018, 07:07 PM   #4
Member
charlie cleveland
PGCA Member

Member Info
 
Join Date: Jul 2009
Posts: 12,986
Thanks: 0
Thanked 7,787 Times in 3,967 Posts

Default

try putting a 16 gauge card board wad under the shot...you can play with the wads till you achive filling the wad to the top....charlie....
charlie cleveland is offline   Reply With Quote
The Following 2 Users Say Thank You to charlie cleveland For Your Post:
Unread 10-25-2018, 08:01 PM   #5
Member
OH Osthaus
PGCA Lifetime
Member
 
Rick Losey's Avatar

Member Info
 
Join Date: Jul 2010
Posts: 7,798
Thanks: 1,641
Thanked 8,138 Times in 3,254 Posts

Default

16 won't fit in the 12 wad - need to see if i have any 20's -

i have used bamboo shavings as fillings before- but have not planed down a rod for a while, i'll have to look behind the bench
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
Rick Losey is offline   Reply With Quote
Unread 10-25-2018, 08:42 PM   #6
Member
edgarspencer
PGCA Member
 
edgarspencer's Avatar

Member Info
 
Join Date: Sep 2011
Posts: 6,059
Thanks: 2,905
Thanked 11,405 Times in 3,075 Posts

Default

Rick, Chedite makes a variety of base heights in their 16ga. hulls, and I suspect they also do in 12ga. hulls
edgarspencer is offline   Reply With Quote
The Following User Says Thank You to edgarspencer For Your Post:
Unread 10-25-2018, 09:06 PM   #7
Member
OH Osthaus
PGCA Lifetime
Member
 
Rick Losey's Avatar

Member Info
 
Join Date: Jul 2010
Posts: 7,798
Thanks: 1,641
Thanked 8,138 Times in 3,254 Posts

Default

Quote:
Originally Posted by edgarspencer View Post
Rick, Chedite makes a variety of base heights in their 16ga. hulls, and I suspect they also do in 12ga. hulls
there is a possibility - i have some other branded Cheditte hulls- i'll look- but its going to have to be a thick basewad
__________________
"If there is a heaven it must have thinning aspen gold, and flighting woodcock, and a bird dog" GBE
Rick Losey is offline   Reply With Quote
Unread 10-25-2018, 10:57 PM   #8
Member
StubTwist
PGCA Member
 
Frank Cronin's Avatar

Member Info
 
Join Date: Jan 2010
Posts: 978
Thanks: 6,180
Thanked 1,601 Times in 483 Posts

Default

Rick, how about a 1/4 felt wad?
Frank Cronin is offline   Reply With Quote
Unread 10-26-2018, 12:50 AM   #9
Member
Bill Jolliff
PGCA Member

Member Info
 
Join Date: Dec 2009
Posts: 596
Thanks: 4,220
Thanked 1,173 Times in 268 Posts

Default

Hey Rick,

I have some 0.135" thick card board wads I use in the bottom of my 3/4 ounce CB wads for my 1/2 ounce loads to bring them up higher so they crimp better.

They are 0.625" diameter (20 gauge) and 0.135" thick. I have some 0.070" thick card boards wads too.

I think I'll be seeing you around lunch time on Saturday and can a bunch of them with me.

Bill
Bill Jolliff is offline   Reply With Quote
The Following User Says Thank You to Bill Jolliff For Your Post:
Unread 10-27-2018, 01:39 PM   #10
Member
Paul Harm
Forum Associate

Member Info
 
Join Date: Nov 2008
Posts: 1,774
Thanks: 44
Thanked 756 Times in 417 Posts

Default

First off, a Remington hull is tapered wall hull[ Win also ] where as the Cheddite is a straight walled hull. That's why the powder is leaking by. Many recipes show a wad for a tapered hull used in a straight walled hull, but you see the problem with that clear hull. Even Claybusters shows their Win/Rem wads being used in straight walled hulls and they make a wad for straight walled hulls. Don't ask me why they list them. Any hull except the Rem/Win is straight walled. To the best of my knowledge the 10ga, 16ga, 20ga, 28ga, and 410 are all straight. The only exception is the Win AAHS hulls. They take a special wad. Second, the RP12 wad is meant for 1 1/2oz of lead shot in a tapered wall hull. Go to BPI and ask what wad to use for a bismuth load. It's different than a lead shot wad. Make sure you mention if they don't ask what hull you're using.
__________________
Paul Harm
Paul Harm is offline   Reply With Quote
Visit Paul Harm's homepage!
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:52 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.