Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions Damascus Barrels & Steel

Notices

Reply
 
Thread Tools Display Modes
Overbored Ithaca Crass?
Unread 03-14-2017, 02:23 PM   #1
Member
Mike Poindexter
PGCA Member

Member Info
 
Join Date: Jun 2009
Posts: 515
Thanks: 566
Thanked 613 Times in 244 Posts

Default Overbored Ithaca Crass?

I have an 1892 Crass Grade 1S, s/n 19508, with 30 inch twist barrels and hand engraving typical of the time. Just a few pics posted below. The reason for this post is I have mic'ed the bores and wall thickness per the attached chart, and was struck by the overbore dimension of .755. Suspicious of back bore and or excessive honing, I noted the barrels had a few moderate pits in the first 6 inches from the breech, and mild pitting or frosting further down, which would contraindicate extensive honing (usually), but the MWT was .033 L and .035 R at 24 inches from the breech and .045 at the proverbial 9 inch mark. Also, the choke constriction measured .020 in the L and .032 in the R. (I know, I checked it three times to make sure I didnt have my hands confused.)
So, the question is, is this a case of possible factory overbore in the 1890-1892 period at Ithaca Gun roughly the same time that Parker Bros. were doing it? Several old threads from Austin and others document that practice, and linked it to the use of brass shells and short step forcing cones. Austin found that .755 was a fairly common nominal 12 ga. bore in the Parker guns before s/n 70,000. Ithaca didnt have the history Parker did, only coming online in 1885 and making their first hammerless Crass in about 1888, but it stands to reason they would have reverse engineered Parker guns for whatever tips they could learn. With the wall thickness and overall barrel condition, I am not hesitant to shoot the gun with low pressure loads, but am just wondering if anybody has run across something like this before. There is nothing in Walt Snyder's book on barrel overboring, and nothing in John Houtchins' book that I could find either. Only TPS and the Parker Pages. Thanks for any insights.
Attached Images
File Type: jpg pix300163062.jpg (32.9 KB, 4 views)
File Type: jpg pix300163125.jpg (33.0 KB, 1 views)
File Type: jpg pix300163156.jpg (37.2 KB, 3 views)
File Type: jpg pix300163203.jpg (54.4 KB, 1 views)
Attached Files
File Type: pdf Ithaca Crass grade 1S Barrel Measurements.pdf (22.6 KB, 11 views)
Mike Poindexter is offline   Reply With Quote
Unread 03-14-2017, 02:33 PM   #2
Member
Dean Romig
PGCA Invincible
Life Member
 
Dean Romig's Avatar

Member Info
 
Join Date: Dec 2008
Posts: 31,557
Thanks: 35,430
Thanked 33,039 Times in 12,321 Posts

Default

The gun doesn't appear to have been refinished and being as nice as it is, I would find it hard to believe it was honed, also judging by the other facts you stated about the barrels.

The reverse chokes seem to indicate the gun was ordered for pass shooting incomers. I have a 10 gauge Parker DH with heavy Damascus 2-frame barrels choked similarly.






.
__________________
"I'm a Setter man.
Not because I think they're better than the other breeds,
but because I'm a romantic - stuck on tradition - and to me, a Setter just "belongs" in the grouse picture."

George King, "That's Ruff", 2010 - a timeless classic.
Dean Romig is offline   Reply With Quote
The Following User Says Thank You to Dean Romig For Your Post:
Unread 03-15-2017, 11:36 AM   #3
Member
Researcher
PGCA Lifetime
Member
 
Dave Noreen's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 3,595
Thanks: 1,616
Thanked 7,770 Times in 2,351 Posts

Default

It has been my experience that the Ithacas I've run a bore mic in have all been over-bored up through the cocking indicator NIDs. I had a 1928 vintage No. 1E 12-gauge with .744" bores. The later NIDs without cocking indicators have been right in the .729", .662", .615" ranges. Maybe over-boring was Uncle Bob's "secret" --

Uncle Bob Edwards.jpg
Dave Noreen is offline   Reply With Quote
The Following 4 Users Say Thank You to Dave Noreen For Your Post:
Unread 03-15-2017, 01:16 PM   #4
Member
Mike Poindexter
PGCA Member

Member Info
 
Join Date: Jun 2009
Posts: 515
Thanks: 566
Thanked 613 Times in 244 Posts

Default

It's really interesting. I have a 1905 Ithaca Field grade Lewis model 16 ga with 26 in nitro steel barrels, believe it is all original, that has .653 and .651 bores, respectively, choked to .643 and .631, IC and Mod. Very mild pitting in the first third. I have no clue what is going on with these bores. You wonder whether there was a concerted plan to bore guns differently, which seems unlikely, or whether they just used barrel reamers until they were so worn that undersized bores resulted, then choked to suit. This doesnt explain the oversized bores in 12 ga, however. I guess I'll just file it away in "imponderables." Thanks
Attached Images
File Type: jpg pix1424166562.jpg (29.3 KB, 2 views)
File Type: jpg pix1424166625.jpg (35.6 KB, 3 views)
File Type: jpg pix1424166796.jpg (60.9 KB, 1 views)
Mike Poindexter is offline   Reply With Quote
Unread 03-16-2017, 05:42 PM   #5
Member
Austin J Hawthorne Jr.
PGCA Member

Member Info
 
Join Date: Aug 2009
Posts: 572
Thanks: 421
Thanked 384 Times in 198 Posts

Default

I don't have any Crass models, but I do have a 1912 vintage 10 gauge Flues with .775 bores in both barrels. I believe that is the standard 10 gauge bore size.
Austin J Hawthorne Jr. is offline   Reply With Quote
The Following User Says Thank You to Austin J Hawthorne Jr. For Your Post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:58 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.