|
 |
 |
|||||||||||||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||||||||||||||
 |
 |
02-10-2014, 08:43 AM
|
#13 | ||||||
|
you have a fine looking old 8 ga ..she looks like shes been hunted with and well taken care of...reckon how many geese and duck s she has put on the table..she s a fine old piece for sure..my old fa loomis and her look to be cousins of sorts except for the under lever..she will make a turkey gun for sure... charlie
|
||||||
|
|
||||||
 |
 |
 |
|
|
|
02-10-2014, 09:11 AM
|
#14 | ||||||
|
Wayne, do you know if that buttplate is original to the gun?
|
||||||
|
|
|
||||||
|
|
|
|
|
|
02-10-2014, 10:00 AM
|
#15 | ||||||
|
It is a shame it is not 4" chambered but you cant have everything. Dean although the but plate fits the gun like it was made for it. I don't think it is the correct pad. Judgeing from my other scott hammergun it should probable be a steel butplate.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
02-10-2014, 10:23 AM
|
#16 | ||||||
|
Wayne, did you just recently pick that one up? If so, I think I might have been following that one. At any rate, I saw an 8ga WC Scott recently online. I really liked the gun and thought it looked like a pretty good buy, but I don't know squat about the brand so I decided to see how long it would sit for my own future pricing knowledge. Wasn't very long. Sold on the second cycle. Just a week or two ago.
__________________
Will makes some excellent points and I agree with all of them. - Dean Romig 03-13-2013 |
||||||
|
|
|
||||||
|
|
|
|
|
|
02-10-2014, 12:25 PM
|
#17 | ||||||
|
Yes I did just buy it. You were probable looking at the same gun. If it hadn't been for one of the other forum members I would not have seen it. W C Scott is a quality English gun manufacturing company. I own two others and in my opinion they are fine guns. The gun was a bargain. It is getting really tough to come by 8ga doubles.
|
||||||
|
|
|
||||||
|
|
|
| The Following User Says Thank You to wayne goerres For Your Post: |
|
|
|
02-10-2014, 01:47 PM
|
#18 | ||||||
|
Wayne:
Don't count on that buttplate NOT being original. It looks correct. There's no rule that says it should be steel. I trust you sent the gun to a responsible 'smith for proper resto of an English gun. |
||||||
|
|
|
||||||
|
|
|
|
|
|
02-10-2014, 04:46 PM
|
#19 | ||||||
|
I asked about the buttplate because I have one that looks almost identical to that one on a 1936 GHE 16 ga in high original condition.
|
||||||
|
|
|
||||||
|
|
|
|
|
|
02-10-2014, 05:15 PM
|
#20 | ||||||
|
I sent the gun to Brad Bachelder. He says he has a formula for casehardening Scotts that is as close as it can get. Brad says he will research the gun and make a determination on the but plate. He will then let me know. I am just not sure. I tried going on line and finding a pic of that plate, But no luck. Dose anybody have any ideas where I could look. The other guns I own do not say W C Scott on the plate. And they are original.
|
||||||
|
|
|
||||||
|
|
|
 |
|
|
Linear Mode
