![]() |
![]() |
![]() |
|||||||||||||||||||||||||||||||||||||||
|
![]() |
![]() |
![]() |
#13 | |||||||
|
![]() Quote:
As old as me? I thought when I met you years ago, that I was in the company of the last living Civil War vet. |
|||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#14 | |||||||
|
![]() Quote:
![]()
__________________
Wag more- Bark less. |
|||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to Daryl Corona For Your Post: |
![]() |
![]() |
![]() |
#15 | ||||||
|
![]()
I just went to the " reloaders network " web site and couldn't find the roll crimpers. Any help ?
__________________
Paul Harm |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#16 | ||||||
|
![]()
On the main page, click ‘Store’, then Shotgun, then the gauge you’re interested in.
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to edgarspencer For Your Post: |
![]() |
![]() |
![]() |
#17 | ||||||
|
![]()
Jay,
I have a 16 gauge precision reloading roll crimper and it works great.
__________________
"Where would a minister be without the help of sin, or the dry without alcohol?" Gene Hill Shotgunner's Notebook "May the honkers fly low and slow." Douglas Bandemer |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#18 | ||||||
|
![]()
Thanks, I found it. Their crimps are a whole lot deeper than mine. I think pressures may raise with a crimp that deep. I could be wrong - maybe someone else can chime in.
__________________
Paul Harm |
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
#19 | |||||||
|
![]() Quote:
The top of the shot only needs to be about 1/8" below the rim of the hull, and the rollover will be 180 degree reversed. With regard to pressure, there's lots of data out there. All I have sent to Precision have been lower than folded samples of like charges. The four shells, below, are, left-right: Factory Eley 2.5" 5/8oz. Once fired Winchester paper Super-X hull, trimmed to 2.4", Fiocchi RO28 wad, 5/8oz. New Cheddite hull, trimmed to 2.5", Fiocchi RO28 wad, 3/4oz New Cheddite hull, trimmed to 2.5", BPI SP28 wad, 5/8 oz The difference between the Cheddite 5/8oz load, and Winchester Paper 5/8oz load is because the Paper hulls had very high base wad. The Winchester Hull with the SP28 wad only allows 9/16oz when trimmed the same. |
|||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to edgarspencer For Your Post: |
![]() |
![]() |
![]() |
#20 | ||||||
|
![]()
good looking roll crimps to me wish mine looked that good....charlie
|
||||||
![]() |
![]() |
![]() |
![]() |
![]() |
The Following User Says Thank You to charlie cleveland For Your Post: |
![]() |
|
|