|
11-18-2020, 09:09 PM | #3 | ||||||
|
Beautiful wood ! Bobby
|
||||||
The Following User Says Thank You to Robert Brooks For Your Post: |
11-18-2020, 09:30 PM | #4 | ||||||
|
I have built a few checkering cradles over the years. I am currently on cradle 3.0 which is a modified versacradle from Berry manufacturing.
For forends I used to just use a large round dowel (like a ladder rung) with a flat cut on it and I would just tape the forend to it with painters tape. It worked fine. The PGCA owns, in their collection, an original checkering jig from the Meriden factory for holding forends. It was on display at the NE maybe 5 years ago and I photographed it with the intension of building one. Earlier this year I made a forend jig for my versacradle that was based on that Meriden factory jig. Here is a photo of the jig that I built. I have used it for a number of other types of forends too, not just parkers. I dont still have a photo of the factory jig on my phone or I would post one. Maybe tomorrow once I get back to my computor if I think of it. And yes, if you see my FB page, there is more on there about it. I think I posted a few videos explaining my checkering cradle setup. AC66F89A-80BF-4424-912A-5866F9174642.jpeg D2A94D5F-94A6-4166-AC57-0F21A4CE2507.jpeg
__________________
B. Dudley |
||||||
The Following 21 Users Say Thank You to Brian Dudley For Your Post: | Alfred Greeson, allen newell, Bob Jurewicz, Cameron Thraen, Chris Robenalt, David Lien, ED J, MORGAN, Eric Johanen, George Davis, hugh rather, J. Scott Hanes, John Knobelsdorf II, Jones Cahill, Larry Mason, Mike Koneski, Paul Ehlers, Randy G Roberts, Robert Brooks, Robert Rambler, Russell E. Cleary, William Woods |
11-19-2020, 10:36 AM | #5 | ||||||
|
Here are some photos of the factory forend checkering jig. This would have been able to be clamped in a vice.
__________________
B. Dudley |
||||||
The Following 35 Users Say Thank You to Brian Dudley For Your Post: | Alfred Greeson, Bill Jolliff, Bob Jurewicz, Brett Hoop, Cameron Thraen, Chris Robenalt, David Lien, Dean Romig, Ed Norman, edgarspencer, Garry L Gordon, George Davis, hugh rather, John Knobelsdorf II, Jones Cahill, Karl Ferguson, keavin nelson, Larry Mason, Mark Garrett, Mark Riessen, Mike Koneski, Mike McKinney, Paul D Narlesky, Paul Ehlers, Pete Kappes, Randy G Roberts, Robert Brooks, Russell E. Cleary, scott kittredge, Steve Huffman, tom leshinsky, Tom Pellegrini, tom roberts, tom tutwiler, Wayne Owens |
04-26-2021, 09:36 PM | #6 | ||||||
|
Really well thought out! Thank you for sharing this idea, love it.
|
||||||
11-19-2020, 07:06 PM | #7 | ||||||
|
Brian, thanks. This is very helpful. I will make one this week. I looked at the Versacradle but too expensive as a project investment. I will make a base like the one in the Parker photos. Appreciate the assistance. Really like your FB pages.
|
||||||
11-19-2020, 07:46 PM | #8 | ||||||
|
See here the high tech and intricate design of my first forend mounting jig. I used this for years.
67F783FF-1D5B-42FA-BE15-8DAECB75469A.jpeg
__________________
B. Dudley |
||||||
The Following 4 Users Say Thank You to Brian Dudley For Your Post: |
11-21-2020, 12:21 PM | #9 | ||||||
|
|
||||||
11-21-2020, 07:32 PM | #10 | ||||||
|
A GH should not be 16. 18 sounds good. They can vary from 18 to 22.
__________________
B. Dudley |
||||||
The Following 6 Users Say Thank You to Brian Dudley For Your Post: |
|
|