Parker Gun Collectors Association Forums

Parker Gun Collectors Association Forums (http://parkerguns.org/forums/index.php)
-   Parker Restoration (http://parkerguns.org/forums/forumdisplay.php?f=8)
-   -   Sleeve my O Frame Hammer 16 (http://parkerguns.org/forums/showthread.php?t=33836)

Bill Murphy 07-26-2021 07:38 AM

Mills, why go to the expense of chamber work and honing? The tubes will be what you are shooting out of.

Mills Morrison 07-26-2021 08:50 AM

I guess to make the tubes fit better

Ken Hill 07-26-2021 10:51 AM

Quote:

Originally Posted by john pulis (Post 339273)
The DH article is in the June 2017 issue of his online journal. He mentioned someone in the US licensed, at that time, by Teague. I wonder who that was.

Here's the link to the Teague lining article https://www.vintageguns.co.uk/magazine/barrel-lining. Quite a few issues are mentioned. Steve Bertram was the US rep for sending barrels to the UK to have them lined.

Ken

William Davis 07-26-2021 03:01 PM

Talked to Briley this morning. To fit my 16 G hammer gun, they machine the tubes to fit the bore. Chambers have to be 2 & 3/4 inch, tubes index depth on the front of the chamber. Fitting 190 dollars over the cost of Tubes. This is not needed on a number of modern factory guns, others it is needed. Short or full length tubes same work required.

May get a 3rd opinion on my barrels . If posable watch the method used and examine through the bore scope myself.

William

Bill Murphy 07-26-2021 05:30 PM

Do what I would do and tell Briley to k/m/a and install the tubes in my barrels. $190 to bore out my chambers is ridiculous.

Dean Romig 07-26-2021 06:36 PM

No way would I have anyone bore out my chambers. I’d keep the original barrels and find and fit another set that I have more faith in.





.

Bruce Hering 07-26-2021 06:39 PM

Quote:

Originally Posted by Garry L Gordon (Post 339232)
Bruce, I read that there were problems with the adhesion method/process of the liners, and that the it is no longer being done. Someone else here I'm sure has a more detailed answer. It sure was a nice solution...if it worked.

Quote:

Originally Posted by john pulis (Post 339235)
There is an article in Diggory Haddock’s online gun journal about Teague tubes posted a few issues ago. As per above, there were adhesion, separation, and corrosion issues if I remember correctly.

Quote:

Originally Posted by John Davis (Post 339257)
Although a moot point now, I have a C grade lifter that I sent to England and had the barrels Teague lined. Never had any issues.

Thanks guys for the comments. Just wondered because the gun that I saw and shot was a great piece of work. Too bad they had problems. As Garry said, "It was a nice solution"

Mills Morrison 07-26-2021 09:33 PM

Quote:

Originally Posted by Dean Romig (Post 339359)
No way would I have anyone bore out my chambers. I’d keep the original barrels and find and fit another set that I have more faith in.





.

My barrels are shot, according to several known experts, otherwise I would have looked at other options.

William Davis 07-26-2021 11:03 PM

And mine may be depending on which expert I listen to. Nice condition O Frame set of Hammer gun barrels rare bird.

William

Mills Morrison 07-27-2021 08:39 AM

I took mine to the Southern and got opinions from several of the best experts. They all pronounced the patient dead though. That would be a good option for you. In your case, you have shot it without problems and may be you just need to keep to the lowest pressure.


All times are GMT -4. The time now is 06:27 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2021, Parkerguns.org