Parker Gun Collectors Association Forums

Parker Gun Collectors Association Forums (https://parkerguns.org/forums/index.php)
-   Parker Reproductions (https://parkerguns.org/forums/forumdisplay.php?f=22)
-   -   Double Trigger conversion (https://parkerguns.org/forums/showthread.php?t=26013)

Brian Dudley 12-20-2018 05:34 PM

Double Trigger conversion
 
3 Attachment(s)
Conversions from Single Trigger to Double trigger have been discussed on the board a few times in the past.

The switch can be accomplished on a basic level by just swapping out parts which results in the function of double triggers, but leaves evidence of the former single trigger on the trigger plate.

This is fine for most guns as heavy modification on the outside is not wanted by most owners. However, if you want to leave no evidence of the conversion having been done, you have to do things the hard way...

The pictured gun is a Repro A-1 in the white. I tig welded up anything related to the single trigger. The long trigger slot was filled in with a cut off piece from another trigger out of the parts bin and then welded. Everything was dressed down and polished out leaving the gun ready for double triggers.

Obviously the same applies to original Parker guns as well. Not just repros.


Attachment 68332

Attachment 68333

Attachment 68334

Greg Baehman 12-20-2018 06:03 PM

1 Attachment(s)
Nice job Brian.

When I had the SST to DT conversion done several years ago to a Repro I once owned, the slot bothered me to the point I ended up selling the gun.

Here's an A-1 Special that, IMO, came up a little short. The end result would have been much better had the owner sought out your services to do it right:

Brian Dudley 12-20-2018 06:18 PM

Oh yeah. If you are starting with new metal, there is no reason not to do it right if the plan is established ahead of time.

That pictured gun is a good example of that. The backwards and out of line hinge pin does not help either.

Greg Baehman 12-21-2018 08:24 AM

Quote:

Originally Posted by Brian Dudley (Post 260892)
Oh yeah. If you are starting with new metal, there is no reason not to do it right if the plan is established ahead of time.

That pictured gun is a good example of that. The backwards and out of line hinge pin does not help either.

Talk about not helping out . . . How about those two unplugged screw holes under the Y-shaped area of the trigger guard? Good grief, one throws a pile of money into a project with a goal of creating a masterpiece and ends with a result like this?? :banghead:

"It's the itty-bitty details that make the big big difference."

Chris Travinski 12-23-2018 08:25 AM

I agree with you guys 100% on this post, it's all in the details. Hinge pin aside, if they put the screws back in the blank holes and case hardened everything to match I think that would have been an acceptable and reversible solution.

Paul Ehlers 12-23-2018 11:51 AM

Brian,

Great job on the trigger slots! Could you show us what you're doing on the other side for mounting the triggers. I know you can remove the single trigger mechanism easily, but am curious if the machining is already there for mounting the double triggers & associated spring.

I'm also curious what your plans are for the safety toggle, being as the single & double triggers use a different mortice in the stock along with different hardware in including the push rod.

Brian Dudley 12-23-2018 12:03 PM

The physical mounting of the triggers is the same on both single and double trigger plates. The mounting of the trigger spring is simply a matter of drilling and tapping a 2-64 hole in the proper place, which I have already done.
I welded up and dressed down the single trigger milling in that area on the back side but have left the milling in the forward areas. No real need to do anything there since it will not be seen and does not effect function of anything.

This particular gun is getting restocked, so the safety mechanism is of no concern. A DT jacket toggle will be inletted into the new stock in the typical fashion.

Paul Ehlers 12-23-2018 06:03 PM

Thanks Brian!!

Ronald Scott 06-21-2019 06:23 PM

Quote:

Originally Posted by Brian Dudley (Post 260888)
Conversions from Single Trigger to Double trigger have been discussed on the board a few times in the past.

The switch can be accomplished on a basic level by just swapping out parts which results in the function of double triggers, but leaves evidence of the former single trigger on the trigger plate.

Hopefully it's ok to jump in on this thread 6 months late....

I have a couple of quick questions regarding "swapping out parts": What parts are needed and are they readily available? From where? Can any decent gunsmith perform this job if he has the parts? Or do I need to find a Parker guy?

I found a nice repro that I like except for the fact that it has a single trigger. Purchase price obviously will have to include cost of the trigger work if I can't find a double trigger gun I like -- how much would you think this job should cost?

Thanks, Ron

Bill Murphy 06-21-2019 07:59 PM

What variety of Repro did you "find" that can't be found with double triggers? There are a bunch of Repros out there.


All times are GMT -4. The time now is 01:17 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2023, Parkerguns.org