Loading the Short Ten by Pete Lester
 

What you need to get into shooting and reloading the (2 7/8") short ten by PGCA member Pete Lester:

A good single stage press - MEC is the most economical.

A short kit for loading 2 7/8" shells.

A hull trimmer - easily made

A hull skivver - optional but handy.

A roll crimper - Ballistic products sells one that goes into a electric drill.

A hull vise - To hold shells while applying a roll crimp

10ga hulls - harder to find and pricier than 12ga

10ga wads - Remington SP10 or BP Decimax/VP100

Filler wads - Fiber is good and economical, 16ga fits nicely in SP10 wad, 1/2" fiber wads are easily split with finger nail if shorter is needed.

Overshot cards - If using a roll crimp.

Recipe's - See Pete Lester's spreadsheet (posted on 5/3/12 at this link) http://parkerguns.org/forums/showthr...rt+spreadsheet

The process of loading the 2 7/8" 10ga is the same as loading any other gauge with the addition of hull trimming and use of a filler wad. It's a pretty simple process.

http://www.youtube.com/watch?v=owXs4Eg__BE[/quote]

Let's not forget a very important item, the scale. Powder charges need to be verified. BP's or Precision Reloading both sell the new digital scales rather cheap.

great advise. i found most of my MEC bushings significantly off for SR7625 according to the chart.

short 10 loads
 

When I started loading for the short 10 I used a roll crimp. I have since switched to a 6 point fold crimp and I am able to get many more loads per hull, and as we know, 10 gauge Federal or Remington hulls are expensive.

since Remington hulls are in such short supply, and Federal are harder to find than Sasquatch - has anyone tried the Cheddite 10 gauge hulls-
of course new low pressure 2 7/8 loads would need to be worked up for them

10 ga Cheddite hulls
 

I am not familiar with the 10 ga Cheddite hull. Maybe Ballistic Products has a supply of them. They are my source for Federal and Remington.

Cheddit 10 ga hulls from Bp are 30.99 per 100.

yes they are - that is why I asked if any one had experience with them.

the question remains

Attached is an update to my Short Ten reloading spreadsheet. It has been a long time since I have come across any new to me data. Last night I found a copy of the First Edition of the Lyman Shotshell Handbook from 1969. I have added 11 new published loads from that book. All of them use discontinued/obsolete hulls. What I found interesting was this is the first time I have found recipes calling for "2 3/4" 10ga hulls. The old recipes also show us again that SR7625 and PB can be good choices for 1 1/4 ounce 10ga loads.

The newest loads are the last ones on page 3 of the spreadsheet.

Pete
Today i set out 20 Remington cases to load the three HS 6 loads with the BPD wad that is in your spread sheet. I Have a cheap Crony for the velocity stats. I have new paper for the pattern board. BPD wads can yield some very good patterns.

I do enjoy your work and enthusiasm with the short ten shotgun, and the loading and shooting of the guns. I have shot these guns for a few years, and I still like to try new loads. I have shot a lot of HS 6 In Alcan brass cases, but mostly heavy loads ((3 and 1/2 IN guns))… I would like to find some data for Win 571 or HS 7 ((ball Powders)) for the short ten.

I have a Charles Daly Linder (( Krupp Barrels)) that the chambers are exactly 2 and 3/4 In. long I cut the shells to fit the chamber length. I roll crimp and load like 2 and 7/8 In. shells. I also shoot gauge mates with 12 Ga. shells. I think maybe it is a uncommon chamber size??? Thanks again for your effort, and information…
David